1600/1827-2
To set alarmsCOUNTDOWN ALARM MODE
1. Press E while in the Alarm Mode to select Alarm 1 through Alarm 5.
Current timeThe countdown timer can be set within a range
Alarm 1Alarm 2Alarm 3Alarm 4Mode indicatorof 1 minute to 24 hours. When the countdown
reaches zero, an alarm sounds for 10 seconds
Hourly Time SignalAlarm 5or until you press any button.
Note that you can also select auto repeat timing
2. After you select an alarm, press A. The hour digits flash on the display becausethat automatically restarts the countdown from
they are selected.
the original value you set whenever zero is
? At this time, the alarm is automatically switched on.
reached.
3. Press B to change the selection in the following sequence.
HourMinutesMonthDateText*To set the countdown start time
1. Press A while in the Countdown Alarm Mode.
HoursSecondsThe hours digit flashes on the display
*There are eight spaces in the text, so you have to press B eight times to move toMinutes
because it is selected.
the Hour setting.
4. Press E to increase the selected digits and D to decrease them. Holding down2. Press B to change the selection in the following sequence.
either button changes the selection at high speed.
? To set an alarm that does not include a month (daily alarm, monthly alarm), set xxHoursMinutes
for the month. Press E or D until the xx mark appears (between 12 and 1) while
3. Press E to increase the selected number. Holding down E changes the selection
the month digits are flashing.
at high speed.
? To set an alarm that does not include date (daily alarm, 1-month alarm), set xx for
? To set the starting value of the countdown time to 24 hours, set 0:00.
the date. Press E or D until the xx mark appears (between 31 and 1) while the4. After you set the countdown start time, press A to return to the Countdown Alarm Mode.
date digits are flashing.
? The format (12-hour and 24-hour) of the alarm time matches the format you select
To use the countdown timer
for normal timekeeping.
1. Press E while in the Countdown Alarm Mode to start the countdown timer.
? When setting the alarm time using the 12-hour format, take care to set the time
2. Press E again to stop the countdown timer.
correctly as morning (no indicator) or afternoon P.? You can continue countdown timer operation by pressing E.
5. If you want to input reminder text, first use B to move the cursor to the text area of
3. Stop the timer and then press D to reset the countdown time to its starting value.
the display and then input text.
? When the end of the countdown is reached and auto repeat timing is off, the alarm
sounds for 10 seconds or until you stop the alarm by pressing any button.
Use D and E to input characters, and B to move the cursor around the display.
For details, see OHow to input characters�.Countdown timing stops, and the countdown time is automatically reset to its
starting value after the alarm stops.
? You can input up to eight characters in the text area.
To switch auto repeat timing on and off
? Anytime while the cursor is on the display, you can press D and E at the same
1. Press A while in the Countdown Alarm Mode.
time to clear it.
6. After you finish inputting data, press A to return to the Alarm Mode.Auto repeat on indicatorThe hours digit flashes on the display
because it is selected.
? If you input reminder text, the text appears on the display when the alarm time is
2. Press D to switch auto repeat on and off.
reached.
? Note that reminder text appears only if the watch is in the Timekeeping Mode when3. Press A to return to the Countdown Alarm
the alarm time is reached. Otherwise, only the alarm tone sounds (without theMode.
reminder text).? When the end of the countdown is reached
while auto repeat is on, the alarm sounds, but
To stop an alarm once it starts to soundthe countdown restarts from the beginning
Press any button to stop an alarm when it starts to sounds. The reminder text for thewithout stopping. You can stop the countdown
alarm (if any) will remain in the text area of the display for about 20 seconds.by pressing E and manually reset to the start
time by pressing D.
To switch an Alarm and Hourly Time Signal on and off
1. In the Alarm Mode, press E to select an alarm or the Hourly Time Signal.
2. When the alarm or Hourly Time Signal you want to is selected, press D to switch it
on and off.
xIndicates alarm is ONSTOPWATCH MODE
y Indicates Hourly Time Signal is ONCurrent time1/100 secondThe Stopwatch Mode lets you measure elapsed
Y If any alarm is on, the Alarm On Indicator is shown on the display when you changetime, split times, and two finishes. The range of
Mode indicator
to another mode.the stopwatch is 23 hours, 59 minutes, 59.99
seconds.
To test the alarm
Hold down E while in the Alarm Mode to sound the alarm.
DUAL TIME MODE
Month-DateThe Dual Time function of this watch lets youHoursSeconds
Mode indicatorkeep track of time in a different time zone.Minutes
? In the Dual Time Mode, the seconds count is
synchronized with the seconds count of the(a) Elapsed time measurement
EEEED
Timekeeping Mode.
StartStopRe-startStopClear
? In the Dual Time Mode, press D to switch
between the 12-hour and 24-hour formats.
(b) Split time measurement
To set the Dual TimeEDDED
1. Press A while in the Dual Time Mode. TheStartSplitSplit releaseStopClear
hour digits flash on the display because they
Hour Minutes Secondsare selected.(c) Split time and 1st-2nd place times
EDEDD
2. Press B to change the selection in the following sequence.StartSplitStopSplit releaseClear
First runnerSecond runnerRecord time
HourMinutesMonthDatefinishes.finishes.of second
Record time ofrunner.
first runner.
3. Press E to increase the selected digits and D to decrease them. Holding down
either button changes the selection at high speed.
4. After you set the time, press A to return to the Dual Time Mode. |
ACEC
