Module No.1600/18271600/1827-1
GENERAL GUIDE
? The operational procedures for Module 1600 and 1827 are identical. All of the illustrations in this manual show Module 1600.
? Press B to change from mode to mode. After you perform an operation in any mode, pressing B returns to the Timekeeping Mode.
? In any mode press C to illuminate the display for about two seconds.
Timekeeping ModeTelememo ModeAlarm ModeDual Time ModeCountdownStopwatch Mode
Alarm Mode
[Module 1827][Module 1600]
TIMEKEEPING MODE? You can input up to eight characters in the text area, and 12 digits in the number area.
? Make sure that you distinguish between the letter O and the number 0 (zero).
Month-Date?In the Timekeeping Mode, press D to switchInputting a zero for the letter O will affect automatic sorting.
between the 12-hour and 24-hour formats.4. After inputting your data, press A to store it and return to the Telememo Mode.Day of week
Year
? When you press A to store data, the message SORT appears on the display for
To set the time and datea few seconds. After the sort operation is complete, the normal Telememo Mode
1. Press A while in the Timekeeping Mode.display (without the cursor) appears.
The seconds digits flash on the display? The text area of the display can show only six characters at a time, so longer text
because they are selected.scrolls continuously from right to left.
2. Press B to change the selection in the? If the message FULL appears in the text area of the display, it means that
following sequence.memory is full. To store more data, you will first have to delete some of the data
stored in memory.
SecondsHourMinutes
HourMinutesDateMonthYearTo recall Telememo data
In the Telememo Mode, press E to scroll forward through stored data items or D to
PM indicatorSecondsscroll in reverse.
3. While the seconds digits are selected (flashing), press E to reset the seconds to? Holding down either button scrolls through the data at high speed.
00. If you press E while the seconds count is in the range of 30 to 59, the seconds
are reset to 00 and 1 is added to the minutes. If the seconds count is in the rangeTo edit Telememo data items
of 00 to 29, the minutes count is unchanged.1. In the Telememo Mode, scroll through the data items and display the one you want
4. While any other digits (besides seconds) are selected (flashing), press E toto edit.
increase the number or D to decrease it.2. Press A and a cursor appears in the text area.
? Holding down either button changes the current selection at high speed.3. Use B to move the cursor to the character you want to change.
? When the 12-hour format is selected, the indicator P appears on the display to4. Change the character.
indicate Op.m.� times. There is no indicator for Oa.m.� times. Selecting the 24-hour? See OHow to input characters� for details.
format causes the indicator 24 to appear on the display.5. After making the changes that you want, press A to store it and return to the
5. After you set the time and date, press A to return to the Timekeeping Mode.Telememo Mode.
? The day of the week is automatically set in accordance with the date.
? The date can be set within the range of January 1, 1995 to December 31, 2039.To delete Telememo data
? If you do not operate any button for a few minutes while a selection is flashing, the1. In the Telememo Mode, scroll through the data items and display the one you want
flashing stops and the watch goes back to the Timekeeping Mode automatically.to delete.
2. Press A and a cursor appears in the text area.
About the backlight3. Press D and E at the same time to delete the data item.
In any mode, press C to illuminate the display for about two seconds.? At this time the cursor appears in the text area, ready for input.
? The backlight of the watch employs an electro-luminescent (EL) light, which loses4. Input data or press A to return to the Telememo Mode.
illuminating power after very long use.
? The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
? The watch will emit an audible sound whenever the display is illuminated. This is
caused by a transformer that vibrates when the EL panel lights up. It does notALARM MODE
indicate malfunction of the watch.
Mode indicatorYou can set five independent alarms with the? If the alarm time you set in the Alarm Mode is reached while the backlight is turned
Month-Datehour, minutes, month and date. You can evenon, the alarm tone will not start to sound until the backlight turns off.
input text that appears on the display to remind
Text area you of the purpose of each alarm. Use the Alarm
Mode to turn the alarm and the Hourly Time
Signal on and off.
TELEMEMO MODE? When an alarm is turned on, an alarm tone
sounds for 20 seconds when the preset time
Mode indicatorThe Telememo Mode lets you store up to 30is reached.
pairs of name and telephone number data. Data
Remaining? When the Hourly Time Signal is turned on,
memoryis automatically sorted based on the charactersthe watch beeps every hour on the hour.
of the name. You can recall data by scrolling
through it on the display.HourMinutes
? See the OCHARACTER LIST� at the back ofAlarm on indicatorAlarm No.
this manual for details on how the watch sorts
data.Alarm Types
? The data item on the display when you exitThe types of alarm you get depends on the information you set.
the Telememo Mode appears first the next
? To set a Daily alarm
time you enter the Telememo Mode.
Set the hour and minutes for the alarm time. Set xx for the month and date (see step
NameTelephone number4 under OTo set alarms�). This type of setting causes the alarm to sound everyday at
the time you set.
To input new Telememo data? To set a Date alarm
1. In the Telememo Mode, press D or E untilSet the month, date, hour and minutes for the alarm time. This type of setting causes
Text area
Cursorthe new data display appears.the alarm to sound at the specific time, on the specific date you set.
? The new data display is the one that is blank
? To set a 1-Month alarm
(contains no name and telephone number).
Set the month, hour and minutes for the alarm time. Set xx for the date (see step 4
? If there is no Telememo data stored in
under OTo set alarms�). This type of setting causes the alarm to sound every day at the
memory yet, the new data display appears as
time you set, only during the month you set.
soon as you enter the Telememo Mode.
2. Press A and a cursor appears in the text area.? To set a Monthly alarm
3. Input a name in the text area and a telephone Set the date, hour and minutes for the alarm time. Set xx for the month (see step 4
number in the number area.under OTo set alarms�). This type of setting causes the alarm to sound every month at
the time you set, on the date you set.
Use D and E to input characters, and B to
move the cursor around the display.
Number area
For details, see OHow to input characters�.
[New Data Display] |
ACEC
