2-2. QW-1825
GENERAL GUIDE
Y Press C to change from mode to mode.
Y In any mode (except when making countdown alarm settings) press D to illuminate the digital display.
Caution
Y The backlight of this watch employs an electro-luminescent (EL) light, which loses its illuminating power after very long term use.
Y Frequent use of the backligfht shortens the battery life.
Y The watch emits an audible sound whenever the display is illuminated. This is because the EL light vibrates slightly when lit. It does not indicate malfunction of the watch.
Timekeeping ModeStopwatch ModeCountdown Alarm ModeAlarm Mode
ABSUN 6 30ST 6 00TR 6 0AL 6
10 58500 00000 00006 45
CE
D
TIMEKEEPNG MODECOUNTDOWN ALARM MODE
Mode indicatorThe countdown alarm can be set within a range of 1
Day of week DayTo set the time and date1/10second to 24 hours. When the countdown reaches
1.Hold down A while in the Timekeeping ModeMonthsecondszero, an alarm sounds for 10 seconds or until you
until the seconds digits flash on the display.press any button.
2.Press C to change the selection (flashing) in theATR 0B
ABSUN 6 30following sequence.To set the countdown start time
SecondsHourMinutes12/24-HourFormat1.Hold down A while in the Countdown Alarm0 0000
CE Mode. The hour setting flashes on the display
10 5850because it is selected.
CE DayMonthYearD 2.Press C to change the selection in the following
Dsequence.
HoursSeconds
HourMinutesSeconds
Hour SecondsMinutes
Minutes
PMindicator
3.While the seconds setting is selected (flashing), press E to reset it to 00. If you
press E while the seconds setting is in the range of 30 to 59, the seconds are reset3.Press E to increase the selected setting or B to decrease it. Holding down either
to 00 and 1 is added to the minutes. If the seconds setting is in the range of 00 tobutton changes the setting at high speed.
Y To set the starting value of the countdown time to 24 hours, set 0:00'00".
29, the minutes count is unchanged.
4.While any other setting (beside seconds) is selected (flashing), press E to increase4.After you set the countdown start time, press A to return to the Countdown Alarm
it or B to decrease it. While the 12/24-hour format setting is selected, press E toMode.
Y If you do not operate any button for a few minutes while a setting is flashing, the
toggle it between 12 and 24.
Y Except for the seconds or 12/24-hour setting, holding down a button changes theflashing stops and the watch goes back to the Countdown Alarm Mode automatically.
setting at high speed.
Y When the 12-hour format is selected, the indicator P appears on the display toTo use the countdown alarm
indicate OP.M.� times. There is no indicator for OA.M.� times.1.Press E while in the Countdown Alarm Mode to start the countdown alarm.
5.After you set the time and date, press A to return to the Timekeeping Mode.2.Press E again to stop the countdown alarm.
Y The day of the week is automatically set in accordance with the date.Y You can resume a paused countdown alarm operation by pressing E.
Y The date can be set within the range of January 1, 1995 to December 31, 2039.3.Stop the countdown alarm and then press B to reset the countdown time to its
Y If you do not operate any button for a few minutes while a setting is flashing, thestarting value.
flashing stops and the watch goes back to the Timekeeping Mode automaticallyY.When the end of the countdown is reached and auto repeat timing is off, the alarm
sounds for 10 seconds or until you stop the alarm by pressing any button.
Countdown timing stops and the countdown time is automatically reset to its starting
value after the alarm stops.
ABOUT THE EL ALARMTo turn auto repeat timing on and off
While the EL alarm feature is turned on, the watch's EL backlight flashes along with1.Hold down A while in the Countdown Alarm Mode until the hour setting flashes.
the audible tone when a daily alarm time is reached, when the hourly time signal2.Press D to turn auto repeat on and off.
sounds, or when the end of a countdown alarm operation is reached. Pressing DAuto repeat indicator
while the EL alarm feature is turned on causes the display to remain illuminated for
five seconds, instead of the normal two seconds when the EL alarm is turned off.
ATR BATR B
To turn the EL Alarm feature on and off
Y In the Timekeeping Mode, hold down B until the EL Alarm indicator appears on (ELPress D
alarm on) or disappears from (EL alarm off) the display.0 15C00E 0 15C00E
EL Alarm indicator
D D
SUN 6 30BSUN 6 30B
OFFON
Hold down B3.Press A to return to the Countdown Alarm Mode.
10 585010 5850Y When the end of the countdown is reached while auto repeat is on, the alarm
ONOFFsounds, but the countdown restarts from the beginning without stopping. You can
DDstop the countdown by pressing E and manually reset to the start time by pressing
B.
Y When the starting value of the countdown time is set at 10 seconds or less and auto
repeat is turned on, the countdown alarm tone sounds for only one second instead
STOPWATCH MODEof the normal 10 seconds. If the EL Alarm is turned on, the EL backlight does not
flash under the above conditions.
Mode indicatorThe stopwatch Mode lets you measure elapsed1/100time, split times, and two finishes. The range of the
seconds
stopwatch is 23 hours, 59 minutes, 59.99 seconds.
ST 6 00You can use the EL backlight at any time while the
B
stopwatch is operating.ALARM MODE
When the Daily Alarm is turned on, the alarm sounds for 20 seconds at the preset
0 0000E time each day. Press any button to stop the alarm after it starts to sound. When the
Hourly Time Signal is on, the watch beeps every hour on the hour.
HoursSecondsMode indicator
Minutes
AAL B
Elapsed time measurementAlarm onindicatorHourly time signal
on indicator
EEEEB
StartStopRe-startStopClear
C6 45E
Split time measurement
EBBEBD
StartSplitSplit releaseStopClear
Split time and 1st-2nd place timesHours
Minutes
EBEBB
StartSplitStopSplit releaseClear
First runnerSecond runnerRecord time of
finishes.finishes.second runner.
Record time of
first runner.
N 4 N |
ACEC
