USEROS GUIDE 2164
General Guide
? If the contents of the display seem to be continually changing, see OAuto Display? Press CCCCC to change from mode to mode.
Function� for information on how to stop it.? In any mode, press LLLLL to illuminate the display for about two seconds.
Timekeeping ModeFile ModeAlarm ModeStopwatch Mode
Timekeeping Mode
This watch lets you select any two of 40 cities (TIME 1, TIME 2) as basic TimekeepingTo switch the auto light switch function on and off
Mode times. Hold down DDDDD to toggle the Timekeeping Mode between TIME 1 and TIME 2.In any mode (except when making any settings), hold down LLLLL for one or two
? You can display either the city code or year. Press AAAAA to toggle between displayseconds to turn the auto light switch function on and off.
of the city code and year.
Auto light
City codeDay of weekYearswitch indicator
Month-DayPress AAAAA.Hold down LLLLL.
TIME 1
Hold down DDDDD.Hold down DDDDD.
ONOFF
Press AAAAA.DST on
TIME 2indicator? The auto light switch indicator is shown on the display in all modes while the auto
light switch function is on.
? In order to protect against running down the battery, the auto light switch function
is automatically turned off approximately three hours after you turn it on. Repeat
the above procedure to turn the auto light switch function back on if you want.
To set the time and date? Pressing LLLLL at any mode (except when making any settings) illuminates the
Setting the time and date for either of the basic times (TIME 1 or TIME 2)display, regardless of the auto light switchOs on/off setting.
automatically adjusts the settings of the other basic time.Caution
? You can turn daylight saving time (DST) on and off independently for TIME 1 and? The backlight of this watch employs an electro-luminescent (EL) light, which loses its
TIME 2.illuminating power after very long term use.
1.While in the Timekeeping Mode, hold down AAAAA until the City Code flashes on the? Frequent use of the backligfht shortens the battery life.
display.? The watch emits an audible sound whenever the display is illuminated. This is because
2.Press CCCCC to change the selection (flashing) in the following sequence.the EL light vibrates slightly when lit. It does not indicate malfunction of the watch.
City CodeDSTSecondsHourMinutesWarning!
? Never try to read your watch when mountain climbing or hiking in areas that are
dark or in areas with poor footing. Doing so is dangerous and can result in
DayMonthYear12/24-HourFormatserious personal injury.? Never try to read your watch when running where there is the danger of accidents,
3.While the seconds setting is selected (flashing), press DDDDD to reset it to 00. If youespecially in locations where there might be vehicular or pedestrian traffic. Doing
so is dangerous and can result in serious personal injury.
press DDDDD while the seconds setting is in the range of 30 to 59, the seconds are
? Never try to read your watch when riding on a bicycle or when operating a
reset to 00 and 1 is added to the minutes. If the seconds setting is in the range ofmotorcycle or any other motor vehicle. Doing so is dangerous and can result in a
00 to 29, the minutes count is unchanged.traffic accident and serious personal injury.
? While City Code setting is selected (flashing), press DDDDD or BBBBB to scroll through the? When you are wearing the watch, make sure that its auto light switch function is
City Code. (For full information on City Code, see the OCity Code Table�.)turned off before riding on a bicycle or operating a motorcycle or any other motor
? While the DST setting is selected, press DDDDD to toggle it ON and OFF.vehicle. Sudden and unintended operation of the auto light switch can create a
? While the 12/24-hour format setting is selected, press DDDDD to toggle it between 12distraction, which can result in a traffic accident and serious personal injury.
and 24.
? While any other setting is selected (flashing), press DDDDD to increase it or BBBBB to
decrease it.File Mode
? Holding down either button changes the setting at high speed.
4.After you set the time and date, press AAAAA to return to the Timekeeping Mode.
? The day of the week is automatically set in accordance with the date.Caution
? The date can be set within the range of January 1, 1995 to December 31, 2039.The following causes all data stored in memory to be deleted. Be sure to always
? If you do not operate any button for a few minutes while a setting is flashing, thekeep separate written copies of all important data.
flashing stops and the watch goes back to the Timekeeping Mode automatically.
YMalfunction or repairs
YDead battery
About the BacklightY Battery replacement
In no event will CASIO be liable for loss of data or any damages arising out of
About the Auto Light Switch Functionsuch loss.
When the auto light switch function is turned on, the backlight automatically turns
on for two seconds under the conditions described below. Avoid wearing the watchMode indicator
on the inside of your wrist. Doing so causes the auto light switch to operate whenThe File Mode lets you store up to 30 pairs of name and
not needed, which shortens battery life.telephone number data. The name can be up to 8
characters long and the number up to 12 digits. Data is
Moving the watch to a position that is parallel to the ground and then tilting itautomatically sorted into alphabetical order based on the
towards you approximately 40 degrees causes the backlight to illuminate.name data. You can recall data by scrolling through it on
the display.
? If you do not operate any button for a few minutes while
in the File Mode, the watch automatically goes back to
Parallel tothe Timekeeping Mode.
ground40°
Number
area
Name area
? The backlight may not illuminate if the face of the watch is more than 15 degrees
off parallel to the left or right. Make sure that the back of your hand is parallel to
the ground.To input File data
Parallel to groundMore than 15 degreesMore than 15 degrees1.In the File Mode, press BBBBB or DDDDD until the new
too hightoo lowdata display appears.
? If the message OFULL� appears on the display, it
means that memory is full. To store more data,
you will first have to delete some of the data.
2.Hold down AAAAA until the flashing cursor appears
on the name area.
3.Use BBBBB or DDDDD to input a character at the cursor
? Static electricity or magnetic force can interfere with proper operation of the autoRemainingposition. The character changes in the
light switch function. If the backlight does not illuminate, try moving the watchmemoryfollowing sequence. Holding down either
back to the starting position (parallel with the ground) and then tilt it back towardbutton changes the character at high speed.
New data display
you again. If this does not work, drop your arm all the way down so it hangs at
your side, and then bring it back up again.
? Under certain conditions the backlight may not light until about one second orPressDDDDD.
Y
less after turn the face of the watch towards you. This does not necessarily(Space)A to Z0 to 9�YY/
indicate malfunction of the backlight.PressBBBBB.
1 |
ACEC
