About the Tide Graph ModeALARM FUNCTIONS
The Tide Graph Mode shows the changing of the tides in graphic form. The graph
When the Daily Alarm is switched on, the alarm sounds for 20 seconds at the preset
uses time (advancing from left to right) as the horizontal axis, and tide change as the
time each day. Press any button to stop the alarm after it starts to sound.vertical axis.
When the Hourly Time Signal is switched on, the watch beeps every hour on the hour.
Y You can enter the Tide Graph Mode by pressing A while in the Moon Data Mode.
Though you can change the time setting while in the Tide Graph Mode, you cannotTo set the alarm time
change the month or day setting. To display the tide graph for another date, return to1.Use C to enter the Alarm Mode.
the Moon Data Mode, change the date setting, and then enter the Tide Graph ModeMode indicatorCurrent time2.Holding down A and the hour digits flash on the
again. Also note that you cannot directly change the month setting in the Moon Datadisplay because they are selected. At this time
Mode. The month setting changes automatically as you increase or decrease thethe Daily Alarm is switched on automatically.
AB
day setting.3.Press C to change the selection in the following
Y The Tidal Graph is also on the display in the Timekeeping Mode, where it indicatessequence.
the tide for the current time.
HourMinutes
CD4.Press D to increase the selected digits and B
to decrease them. Holding down either button
Minuteschanges the selection at high speed.
HighEbbLowFloodHighHoursHourly timeYThe format (12-hour and 24-hour) of the alarm
signal ontime matches the format you select for normal
To display the tide graph for a specific timeand Alarmtimekeeping.
1.Use C to enter the Moon Data Mode.on indicatorYWhen setting the alarm time you using the 12-
Y When you enter the Moon Data Mode fromhour format, take care of set the time correctly as
Flashesanother mode, the display shows the moon upmorning (A) or afternoon (P).
and moon down times for the current date (as5.After you set the alarm time, press A to return to the Alarm Mode.
kept in the Timekeeping Mode).
To switch the daily alarm and hourly time signal on and off
2.Press A to enter the Tide Graph Mode.
APress B while in the Alarm Mode to change the status of the daily alarm and hourlyBY Whenever you enter the Tide Graph Mode, the
time signal in the following sequence.
graph shows the tide movements for 6:00 am of
the current date. Alarm on indicator / hourly time signal on indicator
3.Press D to increase the hour or B to decrease
CDit. Holding down either button changes the hour
at high speed.
Both ONBoth OFFDaily Alarm onlyHourly Time Signal only
SUNRISE / SUNSET FUNCTIONSTo test the alarm
Hold down D while in the Alarm Mode to sound the alarm.
Be sure to set the current time and your current location before trying to use Sunrise /
Sunset functions. The Sunrise / Sunset functions tell you the time of sunrise and
sunsets for specific dates.
To display the sunrise and sunset times for a specific date
STOPWATCH FUNCTIONS
1.Use C to enter the Sunrise / Sunset Mode.
Y When you enter the Sunrise / Sunset Mode for another mode, the display show theThe Stopwatch Functions let you record elapsed time, split times, and two finishes.
sunrise / sunset data for todayOs data (as set in the Timekeeping Mode).The range of the stopwatch is 23 hours, 59 minutes, 59.99 seconds. Stopwatch
2.Press D to advance the date or B to set it back. Holding down either buttonfunctions are available in the Stopwatch Mode, which you can enter using C.
changes the date at high speed.
3.When the date you want is displayed, you will have to wait for about 15 seconds as(a) Elapsed time measurement
1/100
the watch performs its internal calculation before displaying the sunrise/sunset timeMode indicatorsecondDDDDB
for the date.Start StopRe-startStopClear
ASunrise timeSunset timeB
(b) Split time measurement
AB BackDBBDB
StartSplitSplit releaseStopClear
Sunrise/SunsetCD
data search(c) Split time and 1st-2nd place times
CD ForwardSecondsDBDBB
MinutesStartSplitStopSplit release Clear
HoursFirst runnerSecond runnerfinishes.Record timeof second
Datefinishes.
MonthRecord time ofrunner.
first runner.
Notes
Y If you think that the watch is not showing the correct information, check the settings
of the watch in the following order: year, difference from GMT, Longitude, Latitude,
east/west, north/south.
Y Sunrise and sunset times are for sea level locations. Actual times may differ sightly
depending on your elevation.
Y Sunrise and sunset times are correct with a range of 5 minutes at latitudes less than
50, and 10 minutes at latitudes greater than 50.
N 8 N |
ACEC
