2163-2
3.Press DDDDD to increase the selected digits and BBBBB to decrease them. Holding downCITY CODE TABLE
either button changes the selection at high speed.
?The format (12-hour and 24-hour) of the alarm time matches the format you selectCityGMT
for normal timekeeping.CityCodedifferential
?When setting the alarm time using the 12-hour format, take care to set the timeADLADELAIDE+9.5
correctly as morning (no indicator) or afternoon (P).
4.After you set the alarm time, press AAAAA to return to the Alarm Mode.ANCANCHORAGE�09
?If you do not operate any button for a few minutes while a selection is flashing, theBERBERLIN+01
flashing stops and the watch goes back to the Alarm Mode automatically.
BKKBANGKOK+07
To switch the daily alarm and hourly time signal on and offCAICAIRO+02
Press DDDDD while in the Alarm Mode to change the status of the daily alarm and hourlyCCSCARACAS�04
time signal in the following sequence.CHICHICAGO�06
Alarm on indicatorHourly time signal on indicatorDACDHAKA+06
DELDELHI+5.5
DENDENVER�07
DXBDUBAI+04
GUMGUAM+10
HKGHONG KONG+08
Both ONBoth OFFDaily Alarm Hourly TimeHNLHONOLULU�10
ISTISTANBUL+02onlySignal only
JEDJEDDAH+03
To test the alarmJRSJERUSALEM+02
Hold down DDDDD while in the Alarm Mode to sound the alarm.KBLKABUL+4.5
KHIKARACHI+05
LAXLOS ANGELES�08
LONLONDON+00
STOPWATCH MODEMEXMEXICO CITY�06
Mode indicatorThe Stopwatch Mode lets you measure elapsedMIAMIAMI�05
time, split times, and two finishes. The range of
the stopwatch is 59 minutes, 59.99 seconds.MILMILAN+01
MLEMALE+05
NOUNOUMEA+11Current
timeNYCNEW YORK�05
PARPARIS+01
MinutesPPGPAGO PAGO�11
Seconds
RGNYANGON+6.5
RIORIO DE JANEIRO�03
1/100 secondsROMROME+01
SELSEOUL+09
(a) Elapsed time measurementSFOSAN FRANCISCO�08
DDDDDDDDDDDDDDDDDDDDAAAAASINSINGAPORE+08
StartStopRe-startStopClear
SYDSYDNEY+10
(b) Split time measurementTHRTEHRAN+3.5
DDDDDAAAAAAAAAADDDDDAAAAATYOTOKYO+09
StartSplitSplit releaseStopClearWLGWELLINGTON+12
YVRVANCOUVER�08
(c) Split time and 1st-2nd place times
*Based on data as of December 1997.
DDDDDAAAAADDDDDAAAAAAAAAA
StartSplitStopSplit releaseClear
First runnerSecond runnerRecord time of
finishes.finishes.second runner.
Release time of
first runner.
AUTO DISPLAY FUNCTION
The Auto Display function of this watch continually changes the contents of the dis-
play. Note that you cannot use any of the watchOs other functions while the Auto
Display function is operating.
To turn the Auto Display on
Hold down CCCCC for about two or three seconds in any mode until the watch beeps.
To turn the Auto Display off
Hold down CCCCC for about two or three seconds until the watch beeps. At this time the
watch is in the Timekeeping Mode.
Note
The Auto Display function cannot be performed while you are making settings (i.e.
while digits or other setting are flashing on the display). |
ACEC
