1583/1584-2
To input new Telememo data
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes the backlight to light.Text Area1. In the Telememo Mode, press B and D at
Cursorthe same time to display the new data screen.
? The new data screen is the one that is blank
AB
(contains no name and telephone number).
? If the message FULL appears in the text
area of the display, it means that memory is
More
full. To store more data, you will first have to
Parallel tothan
delete some of the data stored in memory.
ground40°CD
2. Hold down A until the flashing cursor
Lappears in the text area of the display.
3. Use B and D to change the character at
Number Areathe cursor position in the text area. The
character changes in the following sequence.
[New Data Screen]
? The backlight turns off in about two seconds, even if you keep the watch
Press DPress B
pointed towards your face.
? The backlight may not light if the face of the watch is more than 15 degreestoA to Z
(space)0 to 9
off the parallel as shown below. Make sure that the back of your hand is(Japanese)(alphabet)
parallel to the ground.
:/.-
Parallel to ground More than 15 degreesMore than 15 degrees
too hightoo low? Holding down either button changes the character at high speed.
? You can input Japanese characters (katakana), English alphabetic characters,
numbers, and symbols in the text area. For a complete list of characters you
can input, see OCharacter List� at the back of this manual.
4. When the character you want is at the cursor position, press C to move the
cursor to the right.
5. Repeat the steps 3 and 4 until your text is complete.
? You can input up to eight characters for the name.
? Static electricity or magnetic force can interfere with proper operation of the6. After you input a name, use C to move the cursor to the number area.
auto light switch. If the backlight does not light, try moving the watch back to? The text area can hold up to eight characters. When the cursor is located at
the starting position (parallel with the ground) and then tilt it back toward youthe eighth space of the text area, moving the cursor to the right causes it to
again. If this does not work, drop your arm all the way down so it hangs atjump down to the first digit in the number area. When the cursor is at the 12th
your side, and then bring it back up again.digit of the number area, moving it to the right causes it to jump back up to
? Under certain conditions the backlight may not light until about one secondthe first character of the text area.
or less after turn the face of the watch towards you. This does not necessarily7. Use B and D to change the character (hyphen, number, or space) at the
indicate malfunction of the backlight.cursor position in the number area. The character changes in the following
sequence.
Warning!
? Never try to read your watch when mountain climbing or hiking in areasPress D
that are dark or in areas with poor footing. Doing so is dangerous andx0 to 9(space)
can result in serious personal injury.Press B
? Never try to read your watch when running where there is danger of
? Holding down either button changes the character at high speed.
accidents, especially in locations where there might be vehicular or
pedestrian traffic. Doing so is dangerous and can result in serious8. When the character you want is at the cursor position, press C to move the
cursor to the right.
personal injury.
? Never try to read your watch when riding on a bicycle or when operating9. Repeat steps 7 and 8 until you complete number input.
? You can input up to 12 digits for the number.
a motorcycle or any other motor vehicle. Doing so is dangerous and
can result in a traffic accident and serious personal injury.10.After inputting your data, press A to store it.
? When you are wearing the watch, make sure that its auto light switch is? When you press A to store data, the message SORT appears on the
turned off before riding on a bicycle or operating a motorcycle or anydisplay for a few seconds. After the sort operation is complete, the cursor
other motor vehicle. Sudden and unintended operation of the auto lightappears in the text area, ready for input a new Telememo data item.
switch can create a distraction, which can result in a traffic accident11.Input more data (staring from step 3) or press A again to return to the
and serious personal injury.Telememo Mode data screen (without the cursor).
? If you do not perform any button operation for few minutes while the cursor is
on the display, the watch automatically returns to the Telememo Mode data
To turn the auto light switch on and off
screen.
In the Timekeeping Mode, hold down D for one second to turn the auto light? The text area of the display can show only five characters at a time, so longer
switch on (AUTO displayed) and ofAUTOf ( not displayed).text scrolls continuously from right to left.
? Frequent use of the auto light switch greatly reduces the charge of the storage
battery. If you use the auto light switch often, be sure to leave the watch
where it is exposed to sunlight during the day time so it can recharge theTo recall Telememo data
storage battery. 10 minutes exposure to sunlight provides enough of a chargeIn the Telememo Mode, press D to scroll forward through stored data items or
for about 10 to 20 auto light switch operations.B to scroll in reverse.
? The AUTO indicator is on the display in all modes while the auto light switch? Holding down either button scrolls through the data at high speed.
is turned on.
To edit Telememo data items
1. In the Telememo Mode, scroll through the data items and display the one
TELEMEMO MODEyou want to edit.
2. Hold down A until the flashing cursor appears in the text area of the display.
Mode indicatorThe Telememo Mode lets you store up to 303. Use C to move the flashing cursor to the character you want to change.
pairs of name and telephone number data.4. Use B and D to change the character.
Data is automatically sorted based on the? For details on inputting characters, see OTo input new Telememo data� (steps
characters of the name. You can recall data3 for name input and 7 for number).
by scrolling through it on the display.5. After making the changes that you want, press A to store them and return
? See the OCHARACTER LIST� at the backto the Telememo Mode data screen.
Nameof this manual for details on how the watch
sorts data.
ABTo delete Telememo data
? If there is no data stored in the Telememo
1. In the Telememo Mode, scroll through the data items and display the one
Mode, the message NO-DATA
Remainingyou want to delete.
appears following the remaining memory
memory2. Hold down A until the flashing cursor appears in the text area of the display.
screen.
3. Press B and D at the same time to delete the data item.
? The data item on the display when you exit
CD? At this time the cursor appears in the text area, ready for input.
the Telememo Mode appears first the next
L4. Input data or press A to return to the Telememo Mode data screen.
time you enter the Telememo Mode.
? In the Telememo Mode, press L to
Telephone numberilluminate the display. Pressing L
illuminates the display even while you are
inputting data. |
ACEC
