Module No. 18691869-1
GETTING ACQUAINTED
Congratulations upon your selection of this CASIO watch. To get the most
out of your purchase, be sure to carefully read this UserOs Guide and keep? The measurement functions built into this watch are not intended for
it on hand for later reference when necessary.taking measurements that require professional or industrial precision.
Values produced by this watch should be considered as reasonable
About this UserOs Guiderepresentations only.
? When engaging in mountain climbing or other activities in which losing
Bearing bezel?Button operations are indicated using the
your way can create a dangerous or life-threatening situation, always
Sensorletters shown in the illustration.
NWbe sure to use a second compass to confirm direction readings.
WN? CASIO COMPUTER CO., LTD. assumes no responsibility for anyAB?Each section of this UserOs Guide provides you
with the information you need to perform
loss, or any claims by third parties that may arise through the use ofoperations in each mode. Further details and
WNSEthis watch.Ptechnical information can be found in the
OREFERENCE� section.
SE
DESC
Graphic area
GENERAL GUIDE
Press D to change from mode to mode. Each mode is explained on theWorld Time ModeAlarm Mode
following pages.
ss
PPA
PCC
Navigation Mode
Timekeeping Modes
Press D.
ABsCountdown Alarm ModeStopwatch Mode
P
C
P
ss
DCPAP
PCPC
BACKLIGHTTo turn the auto light switch on and off
In the Timekeeping Mode, hold down B for two seconds to turn the auto
Auto light switchThe backlight uses an EL (electro-luminescent)light switch on (Auto light switch on indicator displayed) and off (Auto light
on indicatorpanel that causes the entire display to glow forswitch on indicator not displayed).
Aeasy reading in the dark. The watchOs auto lightB? In order to protect against running down the batteries, the auto light switch
switch automatically turns on the backlight whenis automatically turned off approximately six hours after you turn it on.
you angle the watch towards your face.Repeat the above procedure to turn the auto light switch back on if you
P
? The auto light switch must be turned onwant.
(indicated by the auto light switch on indicator)? The auto light switch on indicator is on the display in all modes while the
DC
for it to operate.auto light switch is turned on.
Turning on the Backlight manually
In any mode (except for the World Time Mode), press B to illuminate the
display for about two seconds.TIMEKEEPING MODE
? The above operation turns on the backlight regardless of the current
auto light switch setting.Use the Timekeeping Mode to set the current time and date, to take direction
and temperature readings, and to calibrate the temperature sensor.
About the Auto Light Switch
Turning on the auto light switch causes the backlight to turn on for aboutCalibrating the Seconds Count
two seconds, whenever you position your wrist as described below in anyUse the following procedure to calibrate the
Hour : Minutes
mode.seconds count on a time signal from a radio,Day of week
? See OBacklight Precautions� for other important information about usingTV, or other source.
A
the backlight.B
1. In the Timekeeping Mode, hold down A until
Moving the watch to a position that is parallel to the ground and thenthe seconds digits start to flash on the display.
P
tilting it towards you more than 40 degrees causes the backlight to light.2. Press C to set the seconds count to 00
Cwhen the time signal you are calibrating toD
sounds.
Seconds
More? Pressing C while the seconds count is inPM indicator
Parallel tothanthe range of 30 to 59 resets the seconds to
Month � Day
ground40°00 and adds 1 to the minutes. If the
seconds count is in the range of 00 to 29,
the minutes count is unchanged.
3. Press A to return to the current time display.
Warning!
? Never try to read your watch when mountain climbing or hiking inSetting the Current Time
areas that are dark or in areas with poor footing. Doing so is1. In the Timekeeping Mode, hold down A until
dangerous and can result in serious personal injury.ABthe seconds digits start to flash on the display.
? Never try to read your watch when running where there is danger of? The seconds digits are flashing because
accidents, especially in locations where there might be vehicularthey are selected.P
or pedestrian traffic. Doing so is dangerous and can result in serious2. Press D to move the flashing in the
personal injury.Csequence shown below to select other digitsD
? Never try to read your watch when riding on a bicycle or when operatingand settings.
a motorcycle or any other motor vehicle. Doing so is dangerous and
12/24-Hour
can result in a traffic accident and serious personal injury.SecondsHourMinutes
Format
? When you are wearing the watch, make sure that its auto light switch
is turned off before riding on a bicycle or operating a motorcycle orDayMonthYear
any other motor vehicle. Sudden and unintended operation of the
auto light switch can create a distraction, which can result in a traffic
accident and serious personal injury. |
ACEC
