1978-2
COUNTDOWN ALARM MODEALARM MODE
Mode indicatorThe countdown alarm can be set within a rangeWhen the Daily Alarm is turned on, the alarm sounds for 20 seconds at the preset
1/10of 1 second to 24 hours. When the countdowntime each day. Press any button to stop the alarm after it starts to sound. When the
secondreaches zero, an alarm sounds for 10 seconds orHourly Time Signal is on, the watch beeps every hour on the hour.
until you press any button.
Mode indicator
Alarm on indicator
To set the countdown start time
1.Hold down AA while in the Countdown Alarm
Mode. The hour setting flashes on the display
because it is selected.
2.Press CC to change the selection in theHourly time signal
following sequence.on indicator
HoursSecondsHourMinutesSeconds
Minutes
3.Press EE to increase the selected setting or BB to decrease it. Holding down eitherHours Minutes
button changes the setting at high speed.
? To set the starting value of the countdown time to 24 hours, set 0:00'00"
To set the alarm time
4.After you set the countdown start time, press AA to return to the Countdown Alarm
Mode.1.Hold down AA until the hour setting starts to flash on the display. The hour setting
? If you do not operate any button for a few minutes while a setting is flashing, theflashes because it is selected.
? This operation automatically turns on the Daily Alarm.
flashing stops and the watch goes back to the Countdown Alarm Mode
automatically.2.Press CC to change the selection in the following sequence.
HourMinutes
To use the countdown alarm
1.Press DD while in the Countdown Alarm Mode to start the countdown alarm.3.While the hour or minutes setting is selected (flashing) press EE to increase it or
2.Press DD again to stop the countdown alarm.BB to decrease it. Holding down either button changes the current setting at high
? You can resume a paused countdown alarm operation by pressing DD.speed.
3.Stop the countdown alarm and then press BB to reset the countdown time to its? The format (12-hour and 24-hour) of the alarm time matches the format you select
starting value.for normal timekeeping.
? When the end of the countdown is reached and auto repeat timing is off, the alarm? When setting the alarm time using the 12-hour format, take care to set the time
sounds for 10 seconds or until you stop the alarm by pressing any button.correctly as morning (no indicator) or afternoon (P).
Countdown timing stops and the countdown time is automatically reset to its4.After you set the alarm time, press AA to return to the Alarm Mode.
starting value after the alarm stops.? If you do not operate any button for a few minutes while a setting is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
To turn auto repeat timing on and off
1.Hold down AA while in the Countdown Alarm Mode until the hour setting flashes.To turn the daily alarm and hourly time signal on and off
2.Press DD to turn auto repeat on and off.Press BB while in the Alarm Mode to change the status of the daily alarm and hourly
time signal in the following sequence.
Auto repeat indicator
ALM SIGALMSIG
Both ONBoth OFFDaily AlarmHourly Time
OnlySignal Only
Press DD
? The alarm on indicator (ALM ) and the Hourly Signal on indicator (SIG) are shown
on the display in all modes while these functions are turned on.
OFFON
To test the alarm sound
3.Press AA to return to the Countdown Alarm Mode.Hold down EE while in the Alarm Mode to sound the alarm.
? When the end of the countdown is reached while auto repeat is on, the alarm
sounds, but the countdown restarts from the beginning without stopping. You can
stop the countdown by pressing DD and manually reset to the start time by
pressing BB.
? When the starting value of the countdown time is set at 10 seconds or less and
auto repeat is turned on, the countdown alarm tone sounds for only one second
instead of the normal 10 seconds. If the Flash Alarm is turned on, the EL backlight
does not flash under the above conditions. |
ACEC
