2014-3
3.While the hour, minutes, or seconds digits are flashing, press EEEEE to increase the? To set a date alarm
value or BBBBB to decrease it. Holding down either button changes the value at thighSet the month, day, hour and minutes for the alarm time. This type of setting causes
speed.the alarm to sound at the specific time, on the specific date you set.
4.While the auto repeat indicator is flashing, press EEEEE toggle auto repeat on and off.? To set a 1-month alarm
The auto repeat indicator is on the display only while you are setting the count-
Set the month, hour and minutes for the alarm time. Set Oxx� for the day. This type
down start time.setting causes the alarm to sound every day at the time you set, only during the
Press BBBBBmonth you set.
? To set a month alarm
Set the day, hour and minutes for the alarm time. Set Ox� for the month. This type of
Auto repeat OFFAuto repeat ONthe setting causes the alarm to sound every month at the time you set, on the day you
?To set the starting value of the countdown time to 24 hours, set 0:00' 00".set.
5.After you set the countdown start time and auto repeat timing on and off, press AAAAA
To set the alarm time
to return to the Countdown Alarm Mode.
1.Press EEEEE while in the Alarm Mode to select Alarm 1 through Alarm 3 and Hourly
Time Signal.
To use the countdown alarm
1.Press DDDDD while in the Countdown Alarm Mode to start the countdown alarm.Alarm 1Alarm 2Alarm 3Hourly Time Signal
2.Press DDDDD again to stop the countdown alarm.
?You can resume countdown alarm operation by pressing DDDDD.
3.Press DDDDD to stop the countdown alarm, and then press BBBBB to reset the countdown2.After you select an alarm, hold down AAAAA until the hour digits start to flash on the
time to its starting value.display. The hour digits flash because they are selected. At this time the Alarm is
?When the end of the countdown is reached and auto repeat timing is off, the alarmautomatically switched on.
sounds for 10 seconds or until you stop the alarm by pressing any button. Count-3.Press CCCCC to change the selection in the following sequence.
down timing stops and the countdown time is automatically reset to its starting
value after the alarm stops.HourMinutesMonthDay
To turn the progress beeper on and off
4.Press EEEEE to increase the number or BBBBB to decrease it. Holding down either button
1.While the Countdown Alarm Mode screen shows its starting value or while a count-
changes the current number at high speed.
down operation is in progress, press BBBBB to toggle the progress beeper on and off.
?The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
?When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
OFFON5.After you set the alarm time, press AAAAA to return to the Alarm Mode.
?When the end of the countdown is reached while auto repeat is on, the alarm sounds,?If you do not operate any button for a few minutes while a selection is flashing, the
but the countdown restarts from the beginning without stopping. You can stop theflashing stops and the watch goes back to the Alarm Mode automatically.
countdown by pressing DDDDD and manually reset to the start time by pressing BBBBB.
?If you set a starting time of 10 seconds or less and have Auto Repeat turned on, theTo stop the alarm
countdown alarm tone (which normally sounds for 10 seconds) sounds for only one?Press any button to stop the alarm after it starts to sound.
second.
?When the progress beeper is turned on, the watch beeps as the countdown timeTo switch an alarm on and off
passes the 10, 5, 4, 3, 2, and 1-minute marks, and the 50, 40, 30, 20, 10, 5, 4, 3, 2,General alarm on indicator1.In the Alarm Mode, press EEEEE to select an alarm.
and 1-second marks.2.When an alarm you want to is selected, press BBBBB to
Individual alarm on
indicatorswitch it on and off.
?The individual alarm indicators let you see at a glance
Alarm numberthe on/off status of each alarm. The meaning of these
indicators depend on the mode you are in.
STOPWATCH MODE
Individual alarm on AL-1
HoursThe stopwatch Mode lets you measure elapsed time, splitindicator
Mode indicatortimes, and two finishes. The range of the stopwatch is 23AL-2
hours, 59 minutes 59.99 seconds. You can use the EL
backlight at any time while the stopwatch is operating byAL-3
pressing EEEEE.
?Pressing AAAAA in the Stopwatch Mode While an elapsed?The general alarm indicator is displayed in all modes.
time operation is in progress or while an elapsed time
(other than all zeros) is stopped on the display causesTo switch the Hourly Time Signal on and off
the upper right display to alternate between the currentHourly time signal on1.In the Alarm Mode, press EEEEE to select the Hourly Time
1/100time and stopwatch time.indicatorSignal.
Second2.When Hourly Time Signal is selected, press BBBBB to switch
Minutesit on and off.
Countdown start on?If Hourly Time Signal is on, the Hourly Time Signal On
Secondsindicator is shown on the display when you change to
another mode.
Elapsed time measurement
To test the alarm
Hold down EEEEE while in the Alarm Mode to sound the alarm.
StartStopRe-startStopClear
Split time measurement
StartSplitSplit releaseStopClear
Split time and 1st-2nd place times
StartSplitStopSplit releaseClear
First runner Second runner Record time of
finishes.finishes.second runner.
Record time of
first runner.
Countdown Start
In addition to the normal instant start at the press of a button, the stopwatch can also
be set up to start timing automatically after five seconds have elapsed.
?While the stopwatch is stopped and cleared to all zeros, press AAAAA to toggle count-
down start on and off. Turning on countdown start displays 5" in the lower part of
the display. 00' 00" 00 is displayed when countdown start is turned off. The upper
part of the display always shows the current time.
ALARM MODE
General alarm on indicatorYou can set three independent alarms with the hour,
Individual alarm onminutes, month and day. Use the Alarm Mode to turn the
indicatoralarm and the Hourly Time Signal on and off.
Alarm number?When an alarm is turned on, an alarm tone sounds for
Month20 seconds when the preset time reached.
?When the Hourly Time Signal is turned on, the watchDay
beeps every hour on the hour.
Alarm types
The types of alarm you get depends on the information
you set.
? To set a daily alarm
Set the hour and minutes for the alarm time. Set Ox� for
the month and Oxx� for the day. This type of setting
Modecauses the alarm to sound everyday at the time you set.
indicator Minutes
Hour |
ACEC
