Operation Guide 3319/3781
Setting the Analog TimeProgress Beeper
Perform the procedure below when the time indicated by the analog hands does notWhen the progress beeper is turned on, the watch uses beeps to signal countdown
match the time of the digital display.progress as described below.
" Starting from five minutes before the end of the countdown, the watch emits four
To adjust the analog timeshort beeps at the top of each countdown minute.
1.In the Timekeeping Mode, press C five times to enter" 30 seconds before the end of the countdown, the watch emits four short beeps.
the Hand Setting Mode." The watch emits a short beep for each of the last 10 seconds of the countdown.
2.Hold down A until the current digital time starts to" If the countdown start time is six minutes or greater, the watch emits a short beep for
flash, which indicates the analog setting screen.each second of the final 10 seconds before the five-minute point is reached. Four
3.Press D to advance the analog time setting byshort beeps are emitted to signal when the five-minute point is reached.
20 seconds.
" Holding down D advances the analog time setting atTo configure the countdown timer
high speed.1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
" If you need to advance the analog time setting a long way, hold down D until thecountdown start time starts to flash, which indicates the
time starts advancing at high speed, and then press B. This locks the high-setting screen.
speed hand movement, so you can release the two buttons. High-speed hand" If the countdown start time is not displayed, use the
movement continues until you press any button. It will also stop automaticallyprocedure under OTo use the countdown timer� to
after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal,display it.
or countdown beeper) starts to sound.2. Press C to move the flashing in the sequence shown
4. Press A to exit the setting screen.below to select other settings.
" The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting screen.Start TimeAuto-repeat
" To return to the Timekeeping Mode, press C.
Progress Beeper
3.When the setting you want to change is flashing, use
World TimeB and D to change it as described below.
World Time digitally displays the current time in 27 cities
(29 time zones) around the world.SettingScreenButton Operation
" All of the operations in this section are performed in theStart TimeUse D (+) and B (�) to change the setting.
World Time Mode, which you enter by pressing C." You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
To view the time in another cityAuto-repeatPress D to toggle auto-repeat on ( displayed) and off
In the World Time Mode, press D to scroll eastwardly( displayed).
Module 3319through city codes.Progress BeeperPress D to toggle the progress beeper on (ON) and off
" For full information about city codes, see the OCity Code(OF).
City Current time for the Table�.
code selected city code 4. Press A to exit the setting screen.
" If the current time shown for a city is wrong, it probably
means there is a problem with your Timekeeping Mode" You can also perform steps 1 and 2 of the above procedure whenever you need to
time and/or Home City code settings. Go to theview the current auto-repeat and progress beeper settings.
Timekeeping Mode and make the necessary
adjustments.To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
Module 3781" The countdown timer operation continues even if you
exit the Countdown Timer Mode.
To toggle a city code time between Standard Time and Daylight Saving Time
1.In the World Time Mode, use D to display the city code" Press D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
whose Standard Time/Daylight Saving Time setting you
" To completely stop a countdown operation, first pause it
want to change.
2.Hold down A for about two seconds to toggle between(by pressing D), and then press A. This returns the
countdown time to its starting value.
Daylight Saving Time (DST displayed) and Standard
Time (DST not displayed).
" The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
Module 3319turned on.Stopwatch
" Note that the DST/Standard Time setting affects only theThe stopwatch lets you measure elapsed time, split times,
currently displayed city code. Other city codes are notand two finishes.
affected." The display range of the stopwatch is 59 minutes,
" Note that you cannot switch between Standard Time59.99 seconds.
and Daylight Saving Time while GMT is selected as the" The stopwatch continues to run, restarting from zero
city code.after it reaches its limit, until you stop it.
Module 3781" The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
Module 3319" Exiting the Stopwatch Mode while a split time is frozen
Countdown TimerMinutes 1/100 second on the display clears the split time and returns to
elapsed time measurement.
Seconds
The countdown timer can be set within a range of one" All of the operations in this section are performed in the
minute to 60 minutes. An alarm sounds when theStopwatch Mode, which you enter by pressing C.
countdown reaches zero. The countdown timer also has
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.
" All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressingModule 3781
Module 3319C.
To measure times with the stopwatch
Minutes Seconds Configuring the Countdown TimerElapsed Time
The following are the settings you should configure before
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; ProgressStartStopRe-startStopClear
beeper on/off
" See OTo configure the countdown timer� for informationSplit Time
about setting up the timer.
Module 3781StartSplitSplit releaseStopClear
(SPL displayed)
Auto-repeatTwo Finishes
When auto-repeat is turned on, the countdown automatically restarts from the
countdown start time when it reaches zero. If left running, the countdown is repeated
a total of eight times, after which it stops automatically.StartSplitStopSplit releaseClear
When auto-repeat is turned off, the countdown stops when it reaches zero and theFirst runner Second runner Display time of
display shows the original countdown start time.finishes.finishes.second runner.
" Pressing D while an auto-repeat countdown is in progress pauses the currentDisplay time of
countdown. You can resume the auto-repeat countdown by pressing D, or you canfirst runner.
press A to reset to the countdown time starting value.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
" When the progress beeper is turned off, the countdown end beeper sounds for
about 10 seconds, or until you press any button to stop it.
" When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
2 |
ACEC
