MA0512-EA
Operation Guide 3028
About This Manual
" Depending on the model of your watch, display text
appears either as dark figures on a light background or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
" Button operations are indicated using the letters shown
in the illustration.
" Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the OReference� section.
General Guide
" Press C to change from mode to mode.
" In any mode (except when a setting screen is on the display), press B to illuminate
the display.
Timekeeping ModeStopwatch ModePreset Timer ModeInterval Timer ModeWorld Time ModeAlarm Mode
Press .
TimekeepingTo toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and
Use the Timekeeping Mode to set and view the current24-hour timekeeping.
Hour : Minutes time and date." With the 12-hour format, the P (PM) indicator appears for times in the range of noon
Month - Day to 11:59 p.m. and no indicator appears to the left of the hour digits for times in the
Day of week Read This Before You Set the Time and Date !range of midnight to 11:59 a.m.
The times displayed in the Timekeeping Mode and World" With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
Time Mode are linked. Because of this, make sure youany indicator.
select a city code for your Home City (the city where you" The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
normally use the watch) before you set the time and date.applied in all other modes.
" For full information on city codes, see the OCity Code" The P indicator is not displayed with the Timekeeping Mode time on the Preset
Table�.Timer Mode, Interval Timer Mode, World Time Mode, and Alarm Mode screens.
Seconds
PM indicator
Stopwatch
To set the time and dateThe stopwatch lets you measure elapsed time. The upper
Initial Stopwatch Mode
1.In the Timekeeping Mode, hold down A until theScreendisplay and lower display can be used for official timing of
seconds start to flash, which indicates the settingan event or game.
screen." The measurement range of the upper display is
2.Press C to move the flashing in the sequence shown59 minutes 59 seconds.
below to select other settings." The measurement range of the lower display is
99 minutes 59 seconds.
" The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
" The stopwatch measurement operation continues even
SecondsDSTCity Code HourTimekeeping Mode time
if you exit the Stopwatch Mode.
" All of the operations in this section are performed in the
DayMonthYearMinutesStopwatch Mode, which you enter by pressing C.
3. When the setting you want to change is flashing, use D and B to change it as
described below.Elapsed Time Screen
Minutes SecondsMinutes Seconds
ScreenTo do this:Do this:" Press D to pause and " This time measurement cannot be
restart elapsed time paused.
Reset the seconds to Press D.measurement. It shows the total elapsed time
Toggle between Daylight Saving Time ()since the timing operation started.
and Standard Time ()
Change the city codeUse D (east) and B (west).
" This time measurement (1/100
Change the hour or minutesUse D (+) and B (�).second) cannot be paused.
Change the year
Change the month or dayTo measure times with the stopwatch
" See ODaylight Saving Time (DST)� for details about the DST setting.Elapsed Time
4. Press A to exit the setting screen.Hold down
StartStop*1Re-startStop*1Clear
Daylight Saving Time (DST)*1 Elapsed time measurement in the lower display continues.
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.Using the Watch for Official Timing of a Sport Event
After you set a game or event time, the watch will sound an alarm when the time in
To toggle the Timekeeping Mode time between DST and Standard Timethe lower display reaches that time.
1.In the Timekeeping Mode, hold down A until theIf the event is interrupted for some reason, you can press D to pause and restart
seconds start to flash, which indicates the settingtiming in the upper display. The lower display shows the total elapsed time since the
screen.start of the timing operation. You can calculate the total amount of time that play was
2.Press C to display the DST setting screen.interrupted (lost time or injury time) by subtracting the upper display time from the
3.Press D to toggle between Daylight Saving Timelower display time.
( displayed) and Standard Time ( displayed).
4.Press A to exit the setting screen.
" The DST indicator is on the display while Daylight
DST indicator Saving Time is turned on.
1 |
ACEC
