USER?S GUIDE 2737/2738
World Time
World Time digitally displays the current time in 27 cities4. Press A to exit the setting screen.
City code (29 time zones) around the world.You can also perform steps 1 and 2 of the above procedure whenever you need to
All of the operations in this section are performed in the Worldview the current auto-repeat and progress beeper settings.
Time Mode, which you enter by pressing C.
To use the countdown timer
To view the time in another cityPress D while in the Countdown Timer Mode to start the
In the World Time Mode, press D to scroll eastwardlycountdown timer.
through city codes.The countdown timer operation continues even if you
The city code is displayed for about one second, and thenexit the Countdown Timer Mode.
it is replaced with the current time for that city code.Press D while a countdown operation is in progress to
For full information about city codes, see the ?City Codepause it. Press D again to resume the countdown.
Table?.To completely stop a countdown operation, first pause it
If the current time shown for a city is wrong, it probably(by pressing D), and then press A. This returns the
Current time for the means there is a problem with your Timekeeping Modecountdown time to its starting value.
selected city code time and/or Home City code settings. Go to the
Timekeeping Mode and make the necessary
adjustments.Stopwatch
To toggle a city code time between Standard Time and Daylight Saving TimeThe stopwatch lets you measure elapsed time, split times,
1.In the World Time Mode, use D to display the city codeand two finishes.
whose Standard Time/Daylight Saving Time setting youThe display range of the stopwatch is 59 minutes,
want to change.59.99 seconds.
2.Hold down A for about two seconds to toggle betweenThe stopwatch continues to run, restarting from zero
Daylight Saving Time (DST displayed) and Standardafter it reaches its limit, until you stop it.
Time (DST not displayed).The stopwatch measurement operation continues even
The DST indicator is on the display whenever youif you exit the Stopwatch Mode.
display a city code for which Daylight Saving Time isExiting the Stopwatch Mode while a split time is frozen
turned on.on the display clears the split time and returns to
The Module 2738 DST indicator is displayed as .elapsed time measurement.MinutesSeconds
All of the operations in this section are performed in the
Note that the DST/Standard Time setting affects only the currently displayed cityStopwatch Mode, which you enter by pressing C.
code. Other city codes are not affected.1/100 second
Note that you cannot switch between Standard Time and Daylight Saving Time while
GMT is selected as the city code.To measure times with the stopwach
Elapsed Time
Countdown Timer
StartStopRe-startStopClear
The countdown timer can be set within a range of one
minute to 60 minutes. An alarm sounds when theSplit Time
countdown reaches zero. The countdown timer also has
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.StartSplitSplit releaseStopClear
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressingTwo Finishes
C.
StartSplitStopSplit releaseClear
Configuring the Countdown Timer
First runner Second runner Display time of
The following are the settings you should configure beforefinishes.finishes.second runner.
Minutes Seconds actually using the countdown timer.Display time of
Countdown start time; Auto-repeat on/off; Progressfirst runner.
beeper on/off
See ?To configure the countdown timer? for information
about setting up the timer.
Alarms
Auto-repeat
When auto-repeat is turned on, the countdown automatically restarts from theAlarm timeYou can set five independent Daily Alarms. When an
countdown start time when it reaches zero. If left running, the countdown is repeated(Hour : Minutes)alarm is turned on, the alarm tone sounds when the alarm
a total of eight times, after which it stops automatically.Alarm numbertime is reached. One of the alarms is a snooze alarm,
When auto-repeat is turned off, the countdown stops when it reaches zero and thewhile the other four are one-time alarms.
display shows the original countdown start time.You can turn on an Hourly Time Signal that causes the
Pressing D while an auto-repeat countdown is in progress pauses the currentwatch to beep twice every hour on the hour.
countdown. You can resume the auto-repeat countdown by pressing D, or you canThere are six screens in the Alarm Mode. Four are for
press A to reset to the countdown time starting value.one-time alarms (indicated by numbers from
AL1through AL4), one is for a snooze alarm
Countdown Timer Beeper Operations(indicated by SNZ), and one is for the Hourly Time
The watch beeps at various times during a countdown so you can keep informedSignal (indicated by SIG).
about the countdown status without looking at the display. The following describes theAll of the operations in this section are performed in the
types of beeper operations the watch performs during a countdown.Alarm Mode, which you enter by pressing C.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
When the progress beeper is turned off, the countdown end beeper sounds forOn/Off status
about 10 seconds, or until you press any button to stop it.
When the progress beeper is turned on, the countdown end beeper sounds forTo set an alarm time
about one second.1.In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdowndisplayed.
progress as described below.
Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
30 seconds before the end of the countdown, the watch emits four short beeps.
The watch emits a short beep for each of the last 10 seconds of the countdown.
If the countdown start time is six minutes or greater, the watch emits a short beep for
each second of the final 10 seconds before the five-minute point is reached. Four
short beeps are emitted to signal when the five-minute point is reached.To set a one-time alarm, display one of the screens indicated by an alarm number
from AL1through AL4. To set the snooze alarm, display the screen indicated
To configure the countdown timerby SNZ.
1.While the countdown start time is on the display in theThe snooze alarm repeats every five minutes.
Countdown Timer Mode, hold down A until the current2. After you select an alarm, hold down A until the hour setting of the alarm time
countdown start time starts to flash, which indicates thestarts to flash, which indicates the setting screen.
setting screen.This operation automatically turns on the alarm.
If the countdown start time is not displayed, use the3. Press C to move the flashing between the hour and minute settings.
procedure under ?To use the countdown timer? to4. While a setting is flashing, use D (+) and B (-) to change it.
display it.When setting the alarm time using the 12-hour format, take care to set the time
2. Press C to move the flashing in the sequence showncorrectly as a.m. (no indicator) or p.m. (P indicator).
below to select other settings.5. Press A to exit the setting screen.
Start TimeAuto-repeat
Progress Beeper
3.When the setting you want to change is flashing, use
B and D to change it as described below.
SettingScreenButton Operation
Start TimeUse D (+) and B (-) to change the setting.
You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
Auto-repeatPress D to toggle auto-repeat on ( displayed) and off
( displayed).
Progress BeeperPress D to toggle the progress beeper on (ON) and off
(OF).
2 |
ACEC
