USEROS GUIDE 2597
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of yourAbout This Manual
purchase, be sure to carefully read this manual and keep it on hand for later reference" Button operations are indicated using the letters shown
when necessary.in the illustration.
"Each section of this manual provides you with the
Expose the watch to bright light to charge its battery before using it.information you need to perform operations in each
You can use this watch even as its battery is being charged by exposure to brightmode. Further details and technical information can be
light.found in the OReference� section.
Y Be sure to read OBattery� of this manual for important information you
need to know when exposing the watch to bright light.
If the display of the watch is blank...
If the SLEEP indicator is on the display, it means that the
display is blank because the watchOs Power Saving
function has turned off the display to conserve power.
Power Saving automatically turns off the display and puts
the watch into a sleep state whenever your watch is left for
a certain period where it is dark.
" The initial factory default setting is Power Saving on.
" The watch recovers from the sleep state if you move it to
a well-lit area*, if you press any button, or if you angle
the watch towards your face for reading.
It can take up to five seconds for the display to turn on.
*""""" See OPower Saving Function� for more information.
General Guide
" Press C to change from mode to mode.Countdown Timer ModeAlarm Mode
" In any mode, press B to illuminate the display.
Timekeeping Mode
Press C.
Dual Time ModeStopwatch Mode
Timekeeping
PM indicatorUse the Timekeeping Mode to set and view the currentTo use the countdown timer
time and date.Press D while in the Countdown Timer Mode to start the countdown timer.
Day of week" When the end of the countdown is reached, the alarm sounds for 10 seconds or until
Month � DayTo set the time and dateyou stop it by pressing any button. The countdown time is automatically reset to its
1.In the Timekeeping Mode, hold down A until thestarting value after the alarm stops.
seconds start to flash, which indicates the setting" Press D while a countdown operation is in progress to pause it. Press D again to
screen.resume the countdown.
2.Press C to move the flashing in the sequence shown" To completely stop a countdown operation, first pause it (by pressing D), and then
below to select other settings.press A. This returns the countdown time to its starting value.
" The countdown timer measurement operation continues even if you exit the
12/24-Hour
SecondsHourMinutesCountdown Timer Mode.
SecondsFormat
Hour : Minutes
Power SavingDayMonthYearAlarms
You can set five independent Daily Alarms. When an
3.When the setting you want to change is flashing, usealarm is turned on, the alarm tone sounds when the alarm
D and B to change it as described below.Timekeeping Mode Timetime is reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other four are
SettingScreenButton Operationone-time alarms.
SecondsPress D to reset to 00.You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
Hour, MinutesUse D (+) and B (�) to change the setting." There are five alarm screens numbered 1 through 5.
The hourly time signal screen is indicated by :00.
12/24-HourPress D to toggle between 12-hour (12H) and
Format24-hour (24H) timekeeping." All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Year, Month, DayUse D (+) and B (�) to change the setting.Alarm Time
(Hour:Minutes)
Power SavingPress D to toggle Power Saving on (ON) andAlarm number
off (OFF).
To set an alarm time
1.In the Alarm Mode, use D to scroll through the alarm
4.Press A to exit the setting screen.
screens until the one whose time you want to set is
" See OPower Saving Function� for details about configuring Power Saving settings.
" The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode isdisplayed.
applied in all modes.x1x2x3x4
" The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
:00x5
Countdown Timer" You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2
TimekeepingThe countdown timer can be set within a range of onethrough 5 can be used as one-time alarms only." The snooze alarm repeats every five minutes.
Mode timeminute to 100 hours. An alarm sounds when the2. After you select an alarm, hold down A until the hour setting of the alarm time
countdown reaches zero.
" Countdown timer functions are available in thestarts to flash. This indicates the setting screen.
Countdown Timer Mode, which you enter by pressing3. Press C to move the flashing between the hour and minute settings.
C.4. While a setting is flashing, use D (+) and B (�) to change it.
" When setting the alarm time using the 12-hour format, take care to set the time
To set the countdown start timecorrectly as a.m. (no indicator) or p.m. (P indicator).
1.In the Countdown Timer Mode, hold down A until the5. Press A to exit the setting screen.
Secondshour setting of the countdown start time starts to flash,Alarm Operation
Hours Minuteswhich indicates the setting screen.The alarm sounds at the preset time for about 10 seconds in all modes. In the case of
the snooze alarm, the alarm operation is performed a total of seven times, every five
2. Press C to move the flashing between the hour and minute settings.
minutes, until you turn the alarm off or change it to a one-time alarm.
3. While a setting is flashing, use D (+) and B (�) to change it.
" To set the starting value of the countdown time to 100 hours, set 0:00.
Note
4. Press A to exit the setting screen.
" Pressing any button stops the alarm tone operation.
" Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the Alarm 1 setting screen
1 |
ACEC
