Operation Guide 2759/3344
World TimeTo configure the countdown timer
1.While the countdown start time is on the display in the
World Time digitally displays the current time in 27 citiesCountdown Timer Mode, hold down A until the current
City code (29 time zones) around the world.countdown start time starts to flash, which indicates the
" All of the operations in this section are performed in thesetting screen.
World Time Mode, which you enter by pressing C." If the countdown start time is not displayed, use the
procedure under OTo use the countdown timer� to
To view the time in another citydisplay it.
In the World Time Mode, press D to scroll eastwardly2. Press C to move the flashing in the sequence shown
through city codes.
below to select other settings.
" The city code is displayed for about one second, and then
it is replaced with the current time for that city code.Start TimeAuto-repeat
" For full information about city codes, see the OCity Code
Current time for the Table�.Progress Beeper
selected city code " If the current time shown for a city is wrong, it probably
means there is a problem with your Timekeeping Mode3.When the setting you want to change is flashing, use
time and/or Home City code settings. Go to theB and D to change it as described below.
Timekeeping Mode and make the necessary
adjustments.
SettingScreenButton Operation
To toggle a city code time between Standard Time and Daylight Saving TimeStart TimeUse D (+) and B (�) to change the setting.
1.In the World Time Mode, use D to display the city code" You can set a start time in the range of 1 to 60 minutes in
whose Standard Time/Daylight Saving Time setting you1-minute increments.
want to change.Auto-repeatPress D to toggle auto-repeat on ( displayed) and off
2.Hold down A for about two seconds to toggle between( displayed).
Daylight Saving Time (DST displayed) and StandardProgress BeeperPress D to toggle the progress beeper on (ON) and off
Time (DST not displayed).(OF).
" The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is4. Press A to exit the setting screen.
turned on." You can also perform steps 1 and 2 of the above procedure whenever you need to
" Note that the DST/Standard Time setting affects only theview the current auto-repeat and progress beeper settings.
currently displayed city code. Other city codes are not
affected.To use the countdown timer
" Note that you cannot switch between Standard TimePress D while in the Countdown Timer Mode to start the
and Daylight Saving Time while GMT is selected as thecountdown timer.
city code." The countdown timer operation continues even if you
exit the Countdown Timer Mode.
" Press D while a countdown operation is in progress to
Countdown Timerpause it. Press D again to resume the countdown.
" To completely stop a countdown operation, first pause it
The countdown timer can be set within a range of one
(by pressing D), and then press A. This returns the
minute to 60 minutes. An alarm sounds when the
countdown time to its starting value.
countdown reaches zero. The countdown timer also has
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.
" All of the operations in this section are performed in theStopwatch
Countdown Timer Mode, which you enter by pressingThe stopwatch lets you measure elapsed time, split times,
C.and two finishes.
" The display range of the stopwatch is 59 minutes,
Minutes Seconds Configuring the Countdown Timer59.99 seconds.
The following are the settings you should configure before" The stopwatch continues to run, restarting from zero
actually using the countdown timer.after it reaches its limit, until you stop it.
Countdown start time; Auto-repeat on/off; Progress" The stopwatch measurement operation continues even
beeper on/offif you exit the Stopwatch Mode.
" See OTo configure the countdown timer� for information" Exiting the Stopwatch Mode while a split time is frozen
about setting up the timer.MinutesSeconds on the display clears the split time and returns to
Auto-repeat1/100 secondelapsed time measurement.
" All of the operations in this section are performed in the
When auto-repeat is turned on, the countdown automatically restarts from the
countdown start time when it reaches zero. If left running, the countdown is repeatedStopwatch Mode, which you enter by pressing C.
a total of eight times, after which it stops automatically.
To measure times with the stopwach
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.Elapsed Time
" Pressing D while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing D, or you can
press A to reset to the countdown time starting value.StartStopRe-startStopClear
Countdown Timer Beeper OperationsSplit Time
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.StartSplitSplit releaseStopClear
(SPL displayed)
Countdown End Beeper
Two Finishes
The countdown end beeper lets you know when the countdown reaches zero.
" When the progress beeper is turned off, the countdown end beeper sounds for
about 10 seconds, or until you press any button to stop it.StartSplitStopSplit releaseClear
" When the progress beeper is turned on, the countdown end beeper sounds forFirst runner Second runner Display time of
about one second.finishes.finishes.second runner.
Display time of
Progress Beeperfirst runner.
When the progress beeper is turned on, the watch uses beeps to signal countdown
progress as described below.
" Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
" 30 seconds before the end of the countdown, the watch emits four short beeps.
" The watch emits a short beep for each of the last 10 seconds of the countdown.
" If the countdown start time is six minutes or greater, the watch emits a short beep for
each second of the final 10 seconds before the five-minute point is reached. Four
short beeps are emitted to signal when the five-minute point is reached.
2 |
ACEC
