Operation Guide 3750/4314
World Time3. When the setting you want to change is flashing, use B and D to change it as
described below.
World Time digitally displays the current time in 27 cities
(29 time zones) around the world.SettingScreenButton Operation
" All of the operations in this section are performed in theStart TimeUse D (+) and B (�) to change the setting.
World Time Mode, which you enter by pressing C." You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
To view the time in another cityAuto-repeatPress D to toggle auto-repeat on ( displayed) and off
Module 3750In the World Time Mode, press D to scroll eastwardly( displayed).
Current time for through city codes.Progress BeeperPress D to toggle the progress beeper on (ON) and off
City code the selected " For full information about city codes, see the OCity Code(OF).
city code
Table�.
" If the current time shown for a city is wrong, it probably4. Press A to exit the setting screen.
means there is a problem with your Timekeeping Mode" You can also perform steps 1 and 2 of the above procedure whenever you need to
time and/or Home City code settings. Go to theview the current auto-repeat and progress beeper settings.
Timekeeping Mode and make the necessary
adjustments.To use the countdown timer
Press D while in the Countdown Timer Mode to start the
Module 4314countdown timer.
" The countdown timer operation continues even if you
To toggle a city code time between Standard Time and Daylight Saving Timeexit the Countdown Timer Mode.
1.In the World Time Mode, use D to display the city code" Press D while a countdown operation is in progress to
whose Standard Time/Daylight Saving Time setting youpause it. Press D again to resume the countdown.
want to change." To completely stop a countdown operation, first pause it
2.Hold down A for about two seconds to toggle between(by pressing D), and then press A. This returns the
Daylight Saving Time (DST indicator displayed) andcountdown time to its starting value.
Standard Time (DST indicator not displayed).
Module 3750" The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
DST indicator
turned on.Stopwatch
" Note that the DST/Standard Time setting affects only the
The stopwatch lets you measure elapsed time, split times,
currently displayed city code. Other city codes are not
affected.and two finishes.
" Note that you cannot switch between Standard Time" The display range of the stopwatch is 59 minutes,
59.99 seconds.
and Daylight Saving Time while GMT is selected as the
city code." The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
Module 3750" The stopwatch measurement operation continues even
Module 4314if you exit the Stopwatch Mode.
Seconds 1/100
" Exiting the Stopwatch Mode while a split time is frozen
Minutes second on the display clears the split time and returns to
Countdown Timerelapsed time measurement.
" All of the operations in this section are performed in the
The countdown timer can be set within a range of oneStopwatch Mode, which you enter by pressing C.
minute to 60 minutes. An alarm sounds when the
countdown reaches zero. The countdown timer also has
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.Module 4314
" All of the operations in this section are performed in the
Module 3750Countdown Timer Mode, which you enter by pressingTo measure times with the stopwatch
C.
Minutes Seconds Elapsed Time
Configuring the Countdown Timer
The following are the settings you should configure beforeStartStopRe-startStopClear
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; ProgressSplit Time
beeper on/off
" See OTo configure the countdown timer� for informationStartSplitSplit releaseStopClear
about setting up the timer.
Module 4314Two Finishes
Auto-repeat
When auto-repeat is turned on, the countdown automatically restarts from theStartSplitStopSplit releaseClear
First runner Second runner Display time of
countdown start time when it reaches zero. If left running, the countdown is repeatedfinishes.finishes.second runner.
a total of eight times, after which it stops automatically.Display time of
When auto-repeat is turned off, the countdown stops when it reaches zero and thefirst runner.
display shows the original countdown start time.
" Pressing D while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing D, or you can
press A to reset to the countdown time starting value.Alarms
Countdown Timer Beeper OperationsAlarm time (Hour : Minutes) You can set five independent Daily Alarms. When an
The watch beeps at various times during a countdown so you can keep informedalarm is turned on, the alarm tone sounds when the alarm
about the countdown status without looking at the display. The following describes thetime is reached. One of the alarms is a snooze alarm,
types of beeper operations the watch performs during a countdown.while the other four are one-time alarms.
You can turn on an Hourly Time Signal that causes the
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.watch to beep twice every hour on the hour.
" There are six screens in the Alarm Mode. Four are for
" When the progress beeper is turned off, the countdown end beeper sounds for
one-time alarms (indicated by numbers from
about 10 seconds, or until you press any button to stop it.Alarm Module 3750AL1through AL4), one is for a snooze alarm
" When the progress beeper is turned on, the countdown end beeper sounds fornumber On/Off status
(indicated by SNZ), and one is for the Hourly Time
about one second.
Signal (indicated by SIG).
Progress Beeper" All of the operations in this section are performed in the
When the progress beeper is turned on, the watch uses beeps to signal countdownAlarm Mode, which you enter by pressing C.
progress as described below.
" Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
" 30 seconds before the end of the countdown, the watch emits four short beeps.Module 4314
" The watch emits a short beep for each of the last 10 seconds of the countdown.
" If the countdown start time is six minutes or greater, the watch emits a short beep forTo set an alarm time
each second of the final 10 seconds before the five-minute point is reached. Four1.In the Alarm Mode, use D to scroll through the alarm
short beeps are emitted to signal when the five-minute point is reached.screens until the one whose time you want to set is
displayed.
To configure the countdown timer
1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
" If the countdown start time is not displayed, use the
procedure under OTo use the countdown timer� to" To set a one-time alarm, display one of the screens indicated by an alarm number
display it.from AL1through AL4. To set the snooze alarm, display the screen indicated
by SNZ.
2. Press C to move the flashing in the sequence shown
below to select other settings." The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
Start TimeAuto-repeatstarts to flash, which indicates the setting screen.
" This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.
Progress Beeper4. While a setting is flashing, use D (+) and B (�) to change it.
" When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
2 |
ACEC
