USER?S GUIDE 2463
General Guide
?The illustration below shows which buttons you need to press to navigate
between modes.Moon/Tide Data ModeSunrise/Sunset Mode
C2
2
2
Site Time ModeTimekeeping Mode
Alarm ModeStopwatch ModeCountdown Timer Mode
Press B.
2
222
.2
C
Press C.
Press
Timekeeping
Use the Timekeeping Mode to set and view the current time and date. You canDaylight Saving Time (DST)
also select the Timekeeping Mode display format (Time - Date or Time - TideDaylight Saving Time (summer time) advances the time setting by one hour
Graph) and display color pattern you want to use.from Standard Time. Remember that not all countries or even local areas use
?In the Timekeeping Mode, press D to toggle between the Time - Date andDaylight Saving Time.
the Time - Tide Graph screens.
Time - DateTime - Tide GraphTo toggle the Timekeeping Mode time between DST and Standard Time
PM indicatorYear Month � Day1.In the Timekeeping Mode, hold down A until
the seconds start to flash, which indicates the
setting screen.
2.Press A again to move the flashing to the
Press D.
DST On/Off setting.
23.Press D to toggle between Daylight Saving
Tide graph
2Time (ON displayed) and standard time
(OFF displayed).
4.Press A twice to exit the setting screen.
?The DST indicator appears on the display to
indicate that daylight saving time is turned on.
Day of weekHour : Minutes SecondsMoon phase indicator
Home Site Data
?The tide graph shows tidal movements for the current date in accordanceMoon phase, tide graph data, Site Time Mode times, and Sunrise/Sunset
with the current time as kept in the Timekeeping Mode.Mode data will not be displayed properly unless Home Site data (DST On/Off,
?The Moon phase indicator shows the current Moon phase for the currentlyHome Site name, GMT differential, Longitude/Latitude, and lunitidal interval) is
selected time zone, in accordance with the current date as kept in theconfigured correctly.
Timekeeping Mode.? The initial factory default setting for the Home Site data is TORAMI
(Chiba, Japan). This setting is restored whenever you have the watch?s
Important!battery replaced. Change this setting to match the area where you normally
?Moon phase, tide graph data, Site Time Mode times, and Sunrise/Sunsetuse the watch.
Mode data will not be displayed properly unless the Timekeeping Mode? The GMT differential is the time difference of the time zone where the site is
current date and time settings and Home Site data are configured correctly.located from Greenwich Mean Time.
See ?Home Site Data? on page for more information.? The lunitidal interval is the time elapsing between the Moon?s transit over the
?Always use standard time when setting the Timekeeping Mode time andmeridian and the next high tide. See ?Lunitidal Interval? for more information.
date, even if the area where your Home Site is located is currently in Daylight? This watch displays lunitidal intervals in terms of hours and minutes.
Saving Time (summer time). After setting the time, turn DST on or off as? The ?Site Data List? and ?Lunitidal Interval List? at the back of this manual
required. See ?Daylight Saving Time (DST)? for more information.provide GMT differential, longitude, latitude, and lunitidal interval information
around the world.
To set the time and date
1.In the Timekeeping Mode, hold down A untilTo configure Home Site data
the seconds start to flash, which indicates the1.In the Timekeeping Mode, hold down A until the
GMT differential
setting screen.seconds start to flash, which indicates the setting
2.Press C to move the flashing in the sequencescreen.
shown below to select other settings.?To exit the setting screen at any point, press A
3.When the setting you want to change isa number of times until the Time - Date screen
flashing, use D and B to change it asor Time - Tide graph screen appears. Exiting
described below.the setting screen saves any settings you have
configured up to that point.
2.Press A again to move the flashing to the DST
On/Off setting.
SecondsHourMinutes?Pressing C moves the flashing between the
12/24-Hoursettings in the sequence shown below.
Format
DayMonthYearDST on/off status
DST On/OffGMT differentialSite name
To change this setting Perform this button operation
Seconds Press D to reset to 00.
? The Site name field has spaces for eight characters, so you must press C
Hour, Minutes, Year, to move the flashing goes past the 8th character in order to get to the DST
Use D (+) and B (-) to change the setting.On/Off setting.
Month, Day
3.Press C to move the flashing to the DST On/Off setting.
Press D to toggle between 12-hour (12H)4.Press D to toggle the Daylight Saving Time (ON) and standard time
12/24-Hour Format(OFF).
and 24-hour (24H) timekeeping.5.Press C to move the flashing to the GMT differential setting, and then use
D (+) and B (-) to change it.
? Pressing D while the seconds are in the range of 30 to 59 resets them to6.Press C to move the flashing to the first
00 and adds 1 to the minutes. In the range of 00 to 29, the minutes arecharacter of the site name.
unchanged.7.Input the site name you want.
4.Press A three times to exit the setting screen.?Use D and B to cycle through characters at
? Each press of A in the above step cycles through screens in the followingthe current input position in the sequence
sequence: DST on/off setting screen ? Longitude/Latitude setting screenshown below.
? Timekeeping Mode screen.
? The 12-hour/24-hour timekeeping format you select in the TimekeepingPress D.Press B.
Mode is applied in all modes.
? The day of the week is automatically displayed in accordance with the date(space)A to Z_
(year, month, and day) settings.Site name
0 to 9/.
1 |
ACEC
