MO0302-A
USEROS GUIDE 2534/2654
Getting AcquaintedAbout This Manual
" Button operations are indicated using the letters shown
Congratulations upon your selection of this CASIO watch. To get the most out of yourin the illustration.
purchase, be sure to carefully read this manual and keep it on hand for later reference" Each section of this manual provides you with the
when necessary.information you need to perform operations in each
mode. Further details and technical information can be
Expose the watch to bright light to charge its battery before using it.found in the OReference� section.
You can use this watch even as its battery is being charged by exposure to bright
light.
" Be sure to read OBattery� of this manual for important information you need
to know when exposing the watch to bright light.
(Light)
If the display of the watch is blank...
If the SLEEP indicator is on the display, it means that the
display is blank because the watchOs Power Saving
function has turned off the display to conserve power.
Power Saving automatically turns off the display and puts
the watch into a sleep state whenever your watch is left for
a certain period where it is dark.
" The initial factory default setting is Power Saving on.
" The watch recovers from the sleep state if you move it to
a well-lit area, if you press any button, or if you angle
the watch tow*ards your face for reading.
It can take up to five seconds for the display to turn on.
"*See OPower Saving Function� for more information.
General GuideTelememo Mode
" Press C to change from mode to mode.World Time Mode
" In any mode, press L to illuminate the display.
Timekeeping Mode
Press C.
Stopwatch ModeAlarm ModeCountdown Timer Mode
H
Timekeeping
Use the Timekeeping Mode to set and view the currentTo create a new Telememo record
Hour : Minutes Secondstime and date.1.In the Telememo Mode, use B and D to cycle through
Name area
Yearthe record screens until the new data screen appears.
To set the time and date" The new data screen is the one that is blank (contains
1.In the Timekeeping Mode, hold down A until theno name and telephone number).
seconds start to flash, which indicates the setting" If the message FULL appears on the display, it
screen.means that memory is full. To store another record,
2.Press C to move the flashing in the sequence shownyou will first have to delete some of the records stored
below to select other settings.in memory.
Number area
12/24-Hour 2.Hold down A until the flashing cursor (_) appears in
SecondsHourMinutesNew Data Screenthe name area of the display.
Format
3.In the name area, use D and B to cycle through
Day of week
characters at the cursor position. The characters cycle
Month � Dayin the sequence shown below.
PM indicatorPower SavingDayMonthYear
3. When the setting you want to change is flashing, use D and B to change it as
described below.Press D.
SettingScreenButton Operation
(space)A to Z0 to 9-.:/
SecondsPress D to reset to 00.
Press B.
Hour, MinutesUse D (+) and B (�) to change the setting.
12/24-HourPress D to toggle between 12-hour (12H) and4. When the character you want is at the cursor position, press C to move the cursor
Format24-hour (24H) timekeeping.to the right.
5. Repeat steps 3 and 4 until the name is complete.
Year,Month,DayUse D (+) and B (�) to change the setting.Y You can input up to eight characters for the name.
Power SavingPress D to toggle Power Saving on (ON) and6. After you input the name, press C as many times as necessary to move the cursor
off (OFF).to the number area.
Y When the cursor is located at the eighth space of the name area, moving the
4. Press A to exit the setting screen.cursor to the right causes it to jump to the first digit of the number. When the
" See OPower Saving Function� for details about configuring Power Saving settings.cursor is at the 12th digit of the number, moving it to the right (by pressing C)
" The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode iscauses it to jump to the first character in the name.
applied in all modes.7. In the number area, use D and B to cycle through numbers and symbols
" The day of the week is automatically displayed in accordance with the date (year,(hyphen, space) at the cursor position. The characters cycle in the sequence shown
month, and day) settings.below.
Press D.
0 to 9(space)
Telememox
Press B.
Remaining memoryThe Telememo Mode lets you store up to 30 records, each
containing name and telephone number data. Records are8. When the character you want is at the cursor position, press C to move the cursor
automatically sorted based on the characters of the name.to the right.
You can recall records by scrolling through them on the9. Repeat steps 7 and 8 until you complete number input.
display.Y You can input up to 12 digits for the number.
" See OSort Table� for details on how the watch sorts10. After inputting your data, press A to store it.
Namerecords.Y After data storage is complete, the cursor appears in the name area of the
" All of the operations in this section are performed in thedisplay, ready for input of a new Telememo record.
Telememo Mode, which you enter by pressing C.11. Input more data (starting from step 3) or press A again to return to the Telememo
record screen (without the cursor).
Y The name can show only three characters at a time, so longer text scrolls
continuously from right to left. The last character is indicated by the symbol after it.
Telephone number
1 |
ACEC
