2169/2299-2
STOPWATCH MODEALARM MODE
The Stopwatch Mode lets you measure elapsed time, split times,You can set five independent Daily Alarms. When a Daily Alarm is
Mode indicatorMode indicator � Alarm No.
and two finishes. You also get Auto-Start function. The range of theturned on, the watch beeps for 20 seconds at the alarm time each
Graphic area
stopwatch is 59 minutes, 59.99 seconds.day. Press any button to stop the alarm after it starts to sound.
" In the Stopwatch Mode, press BBBBB to illuminate the display for aboutWhen the Hourly Time Signal is turned on, the watch beeps every
three seconds.hour on the hour.
" In the Alarm Mode (including alarm time setting), press EEEEE to illu-
To measure elapsed timeminate the display for about three seconds.
1.Press EEEEE to start the stopwatch." The graphic area in the Alarm Mode shows the current on/off sta-
2.Press EEEEE to stop the stopwatch.tus of each of the five alarms.
" You can resume the measurement operation by pressing EEEEE again.
Minutes3.Press DDDDD to clear the stopwatch to all zeros.
SecondsHour : Minutes
1/100 secondAlarm on indicator
To record split timesAM indicator
1.Press EEEEE to start the stopwatch.
To set an alarm time
2.Press DDDDD to display the timing up to that point. Stopwatch timing continues internally.
1.Press DDD while in the Alarm Mode to select the alarm whose time you want to set.
3.Press DDDDD to clear the split time and to continue time measurement on the display.DD
" You can repeat steps 2 and 3 as many times as you want.
4.Press EEEEE to stop the time measurement.Alarm 1Alarm 2Alarm 3Alarm 4
5.Press DDDDD to clear the stopwatch to all zeros.
Hourly Time SignalAlarm 5
To time first and second place finishes
2.After you select an alarm, hold down AAAAA until the hour digits start to flash on the display. The
1.Press EEEEE to start the stopwatch.
hour digits flash because they are selected.
2.Press DDDDD when the first finisher crosses the line, and record the time." This operation automatically turns on the alarm.
3.Press EEEEE when the second finisher crosses the line.3.Press CCCCC to change the selection in the following sequence.
4.Press DDDDD to display the finishing time of the second finisher.
5.Press DDDDD again to clear the stopwatch to all zeros.HourMinutes
About the Auto-Start function4.Press DDDDD to increase the selected digits. Holding down DDDDD changes the selection at high
With the Auto-Start function, the watch performs a 5-second countdown. When the countdownspeed.
reaches zero, stopwatch operation starts automatically. During the final three seconds of the" The format (12-hour and 24-hour) of the alarm time matches the format you select for normal
countdown, a beeper sounds with each second.timekeeping.
To use the Auto-Start function" When setting the alarm time using the 12-hour format, take care to set the time correctly as
1.While the stopwatch display is showing all zeros (00'00"00) ina.m. (A indicator) or p.m. (P indicator).
the Stopwatch Mode, press DDDDD.5.After you set the alarm time, press AAAAA to return to the Alarm Mode.
" At this time the auto-start indicator appears on the display to indi-" If you do not operate any button for a few minutes while a selection is flashing, the flashing
cate that auto-start is on. Press DDDDD again to turn auto-start off (in-stops and the watch goes back to the Alarm Mode automatically.
dicated when the auto-start indicator is not on the display).
2.Press EEEEE to start the countdown.To turn an alarm and the Hourly Time Signal on and off
" Pressing EEEEE also causes the countdown time to appear on theGraphic area1.In the Alarm Mode, press DDDDD to select an alarm or the Hourly
display.Time Signal.
2.Press BBBBB to toggle the select item on and off.
Auto-start indicator" The indicators ALM and appear on the display whenever
an alarm is turned on.
" When the countdown reaches zero, a tone sounds, the backlight illuminates the display, and" The indicators SIG and appear on the display whenever
a stopwatch timing operation starts automatically.the Hourly Time Signal is turned on.
" To stop the Auto-Start countdown and return to the all-zeros display, press DDDDD." Indicators in the graphic area of the Alarm Mode show which
" Pressing EEEEE while the Auto-Start countdown is in progress immediately starts the stopwatch.alarms are turned on.
Alarm on indicator
" In other modes (besides the Alarm Mode), the ALM indicator
Alarm 5 (off)remains on the display as long as at least one of the alarms
Alarm 2 (off)is on, while the SIG indicator remains on the display while
the Hourly Time Signal is on.
Alarm 1
(on)
To test the alarm
Hold down BBB while in the Alarm Mode to sound the alarm.
Alarm 3 (on)BB
Alarm 4 (off) |
ACEC
