MA0404-EA
Operation Guide 2879/2889
About This Manual
" The operational procedures for Modules 2879 and 2889
(Light)are identical. All of the illustrations in this manual show
Module 2879.
" Button operations are indicated using the letters shown
in the illustration.
" Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
Module 2879found in the OReference� section.
(Light)
Module 2889
General Guide
" Press B to change from mode to mode.
" In any mode, press L to illuminate the display.
Timekeeping ModeAlarm ModeStopwatch ModeDual Time Mode
Press .
TimekeepingAlarm
Use the Timekeeping Mode to set and view the currentWhen the daily alarm is turned on, the alarm tone sounds
PM indicatortime and date.Timekeeping Mode timewhen the alarm time is reached.
(Hour : Minutes)
Day of weekYou can also turn on an Hourly Time Signal that causes
Mode indicator
Month - Day To set the time and datethe watch to beep twice every hour on the hour.
1.In the Timekeeping Mode, hold down A until the" All of the operations in this section are performed in the
seconds start to flash, which indicates the settingAlarm Mode, which you enter by pressing B.
screen.
2.Press B to move the flashing in the sequence shownAlarm Operation
below to select other settings.The alarm tone sounds at the preset time for 10 seconds,
regardless of the mode the watch is in.
SecondsHourMinutes
SecondsAlarm time
Hour : MinutesDay of weekDayMonthYear(Hour : Minutes)
To set an alarm time
3. When the setting you want to change is flashing, press C to change it as1.In the Alarm Mode, hold down A until the hour setting
described below.starts to flash, which indicates the setting screen.
To change this settingPerform this button operation" This operation automatically turns on the alarm.
2.Press B to move the flashing between the hour and
SecondsPress C to reset to 00.
minutes.
Hour, Minutes, Year, Month,Press C to increase the setting.3.While a setting is flashing, use C to increase it.
Day, Day of weekHolding down C changes the setting at high speed.
Holding down C changes the setting at high speed.
" Pressing C while the seconds are in the range of 30 to 59 resets them to 00 and" With the 12-hour format, set the time correctly as a.m.
(no indicator) or p.m. (P indicator).
adds 1 to the minutes. In the range of 00 to 29, the minutes are unchanged.
4.Press A to exit the setting screen.
4. Press A to exit the setting screen.
" The year can be set in the range of 2000 to 2099.
" The watchOs built-in full automatic calendar makes allowances for different monthTo stop the alarm tone after it starts to sound
lengths and leap years. Once you set the date, there should be no reason to changePress any button.
it except after you have the watchOs battery replaced.
To turn the Daily Alarm and Hourly Time Signal on and off
To toggle between 12-hour and 24-hour timekeepingIn the Alarm Mode, press C to cycle through the on and
In the Timekeeping Mode, press C to toggle between 12-hour timekeeping andHourly time signaloff settings as shown below.
24-hour timekeeping.on indicator
Alarm On Indicator/Hourly Time Signal On Indicator
" With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
" With the 24-hour format, times are displayed in the range of 0:00 to 23:59. 24-hourBoth onBoth offDaily alarm Hourly Time
format is displayed as 24 on the Module 2879 display, and 24H on the Module 2889onlySignal only
display.
" The P and 24-hour format (24, 24H) indicators are not displayed with theAlarm on indicator " The alarm on (ALM) indicator flashes while the alarm is
Timekeeping Mode time on the Alarm Mode and Dual Time Mode screens.sounding.
" The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is" The alarm on (ALM) indicator and Hourly Time Signal
applied in all other modes.on (SIG) indicator are displayed in all modes.
To test the alarm
In the Alarm Mode, hold down C to sound the alarm.
1 |
ACEC
