ENGLISH
DESCRIPTION
The appliance can be used both in Ducting version and Filtering version. In the Ducting version (Fig. 1), cooking
vapours and/or odours are conveyed straight outside (ceiling and/or wall) by a disposal duct, using the holes that are
predisposed on the top and/or at the back of the apparatus. In the Filtering version (Fig. 2) cooking vapours and/or odours
are depurated by a special charcoal filter and recirculated around the room by the front fissures. ATTENTION: For the
filtering version it is absolutely necessary to use the special charcoal filter whereas for the ducting version it is not.
INSTALLATION
Before assembling the appliance it is necessary to take off the anti-grease grille. To take off the grill it is necessary
to push this one towards the rear of the apparatus, by means of the proper knobs, so that it gets released, and to pull it
downwards; to take it off completely, make it rotate on one side keeping the other one steady (Fig. 3).
Installation in extraction version: depending on your requirements, choose which opening to use for the air outlet (rear
or upper) and fit the flange (A) provided, proceeding as follows: make the 3 flange tabs and stop (C) coincide with the slots
on the hood; turn the flange slightly clockwise until it locks into position (Fig. 4). On the other opening, fit the cap (B) provided
and make the 3 cap tabs and stop (D) coincide with the slots on the hood; turn the cap slightly clockwise until it locks into
position.
Installation in filter version: on both the openings (rear and upper), fit the caps (B) provided, making the 3 cap tabs and
the stop (D) coincide with the slots on the hood; turn the cap slightly clockwise until it locks into position.
The following operations are essential for assembly: - Install a proper wiring system. - If your apparatus is to be
assembled as a Ducting appliance, you must first make the air venting hole and get a proper pipe to connect the hole to
the flange of the hood.
Wall fitting: Making use of the appropriate drilling jig, apply the supplied blocks into the wall. Insert two of the supplied
screws so that the apparatus can be hooked onto these ones by means of the holes provided on the appliance (Fig. 5A).
Once the apparatus is hooked, fix it definitively to the wall using the two other screws and the holes made at its bottom
(Fig.5B). To avoid damage make exclusive use of the holes already prepared on the hood. Make the electrical connections.
Wall cupboard fitting: Using the appropriate drilling jig make the four fixing holes into the bottom of the wall cupboard
and cut the air venting hole if the hood is a ducting version one (for the filtering version this hole is not necessary). Holding
the hood against the bottom of the cupboard fix it to it by means of the supplied four screws (Fig. 6). Make the electrical
connections.
IMPORTANT: Check the position of screw A (Fig. 7). For the ducting version screw A must be completely
screwed; for the filtering version the screw must be completely unscrewed to let the sucked air to get
out through the top fissures.
OPERATION
The hoods are provided with the following type of controls:
Controls of Fig. 8: A = light switch. B = first speed motor ON/OFF switch. C = second speed switch. D = third speed
switch. E = warning light: indicates motor operation.
Controls of Fig. 9: A = light switch; position 0: light off; position 1: light on. B = motor switch; position 0: motor off;
position 1-2-3: motor first, second and thrid speed motor on. C = warning light: indicates motor operation.
Filtering/ducting conversion: the conversion can be done in the inside of the appliance. Access is possible by
opening the grille as described beforehand. Verify that screw A (Fig. 7) is completely unscrewed, so that the inside valve
let the air to be conveyed again into the room throuth the slots. Insert the charcoal filter (Fig. 2F and 7F): lift the two stops
made of metallic wire (Fig. 7C); insert the charcoal filter and set back the two stops.
In case the hood is a filtering version one, it is necessary to change the charcoal filter (Fig. 2F and 7F) according to
utilization about every six month. To remove the charcoal filter: -take off the anti-grease grill: by means of the proper
knobs make the grill move towards the rear of the apparatus and drop the front part of it; now, keeping the right (or left)
side of the grill steady, make the opposite side rotate so that it gets off the hood (Fig. 3). - lift the two metallic stops (Fig.7C).
- remove the charcoal filter.
The anti-grease filtering panelis easily removed from the grille by opening it as described above and lifting the two
stops made of metallic wire (Fig. 7C). In the filtering version, to get access to the anti-grease panel the charcoal filter must
be removed too. Change the anti-grease panel according to use. If the panel is a metallic one it can be washed with some
neutral detergent by hand or in a dish-washer.
To gain access to the light bulb(s), remove the anti-grease grill as described above and remove the bulb(s). Replace
with lamps of the same type. |
ACEC
