C6242 A3 81091 8pp Brdsht 21/11/02 3:24 PM Page 1
INSTALLATIONOPERATION
INSTALLATION OF THE DRAIN KIT5. Screw the nut onto the connector on the back of the machineOpen the door.AFTER REMOVING THE DRIED CLOTHES
and position the elbow so that the hose will fit into the waste-
Your dryer may be supplied with a drain kit. This can be fitted soLoad clothes loosely into the drum.
pipe. Shorten the hose if necessary. Tighten the nut.
that the condensed water can be emptied into a waste-pipeLoad sheets first starting with one corner.ALWAYS CLEAN THE FILTER.Failure to do so could cause the
instead of the water bottle in the machine. If a kit is not supplied,6. Move the machine into its working position with the drainClose the door.safety cut-out to operate.
one can be obtained from yourhose inserted into the waste pipe.Dry your hands.
dealer.� Pull the filter upwards and away from
Plug in the machine.
50mm
the appliance.
The illustration shows the600mmSelect either dry or extra dry, using the button.
minimum space required by thePress the start button.
� Remove any threads or fluff by hand or
dryer and the position of the
The drum will rotate in an anticlockwise direction, with all thewith a soft brush.
waste-pipe within this space and
drying status lights (if fitted) illuminating in sequence i.e.
behind the dryer. If a trap is fitted
Red/Amber/Green/Green.� Slide the filter back.
it must not obstruct the air inlet atLK
J
If the machine has no load in the drum it will switch off
the back of the dryer.
�W ash the filter occasionally in detergent
automatically after approximately 40 seconds
The waste pipe can be positionedFINAL INSTALLATIONsolution using a soft brush to remove
The drum will now begin to rotate and will stop automatically
on either side of the dryer.small particles.
Push the filter into its operatingwhen your clothes are dry. The drum will stop and turn in the
If the waste pipe is used by bothposition as shown in the diagram.other direction for a short while every few minutes.
the dryer and a washing machine then its diameter must be
If you wish to change the side onThere is an automatic 12 minute cool down period at the end of
large enough to contain both hoses - 1.5� bore (38mm)
which your door opens, see theevery cycle, during which the heater is switched off. This helps
minimum.
instructions on the back page.to minimise creasing. The dryer on neon will remain lit until theALWAYS EMPTY THE WATER BOTTLE
1. Unscrew the plastic nJ from the connector at the toput , rearRemove any dust by wiping theend of the cycle.
of the machine. Remove and discard the plastic disc.drum and door with a damp cloth.KeepAt the end of the cycle the neon will flash to indicate that the
the rubber washer K.Any initial smell from the heaterdryer is in anti-crease. The drum will rotate periodically until you�Open the door, pull out and empty the
bottle.
2. Push the flanged tube L into the connector as shown untilshould disappear after the firstopen the door or disconnect from the mains to stop it.This helps
period of heating.
the flange is fully seated.to minimise creasing.
� Replace the bottle ensuring that it is
Position the tumble dryer so that
If the door is opened during a cycle the dryer will stop. If a load
3. Push the free end of the hose through the threaded end ofpushed all the way in - if it is not, the
the plug remains accessible afteris checked mid cycle restart the appliance by, closing the doordryer will not operate.
the nut and pull through so that the flange of the plastic
installation. Do not block the vent atand pressing the start button. When drying large items such as
elbow, at the other end of the hose is seated against the
the front of the dryer, as this will� If the dryer is connected to a drain there
inside of the nut.sheets, we suggest you periodically stop the dryer to redistribute
impair the working of the machine.the load.is no need to empty the bottle but it must
4. Insert the rubber wKasher .be correctly fitted to the machine.
NEVER SWITCH THE DRYER OFF AND LEAVE A HOT LOAD
IN THE DRUM.
THE CONTROLSPREPARATIONADDITIONAL INFORMATION
ANY PROBLEMSOPTIONAL EXTRAS
CARE LABELS YOU MAY FIND ON YOUR
If the clothes are not dryafter normal drying time:Drain Hose Kit
FABRICS
� Check that the lint filter has been cleaned. A blocTok ed filter willenable your dryer to be connected to a drain to remove the
restrict the airflow.need to empty the water bottle.
� Check that the machine has the correct weight load in theThe above item can be purchased as an accessory for your
Suitable for tumble drying
drum, this machine will stop after approximately 40 secondstumble dryer from your supplier.
if the drum is empty.
Tumble dry using full heat
� Check that the door striker is in place if the machine is a large
Tumble dry using half heatdoor opening model.
TECHNICAL DATA
� Check that the condenser unit and associated duct work are
A. THE WATER BOTTLE (Behind the pull-down door): Must be
Do not tumble dry
emptied after every cycle (except when a drain hose kit is fitted).clean. If blocked these will restrict the airflow.
B. BOTTLE FULL LIGHT: This will light up and the machine will� Check that your dryer is heating - below the door to the leftOVERALL DIMENSIONS:
stop if the water bottle is full or if it has not been pushed fullyDo not tumble dry woollen or wool mixture articles unless theside, should feel warm to the touch after the first 10-15Height: 85 cm
back into the correct position. If the bottle is remoarticle is labelled to be suitabved andle due to a possibility of shrinkagemin.
utes of its programme. Failure to heat may indicate theWidth: 59.5 cm
replaced during the cycle the start button must be pressed to
safety cut-out has operated. To reset, simply press the red
Depth: 58 cm
restart the dryer.Roll dripping wet articles in a towel to remove excess water.
button at the rear of the machine. If it has operated then a
C. FINAL DRYNESS: Select the desired final dryness of the load
Place delicate articles e.g. tights, scarves, inside a pillowcase.sharp Oclick� will be heard. This cut-out only operates if the
with a choice of a dry or extra dry setting.MAXIMUM DRY WEIGHT LOADS:
airflow is severely restricted so make sure the filter is clean
D. DRYING STATUS. (IF FITTED)To avoid the need to iron easycare polyester/cotton items it is
and that all other restrictions are removed before re-starCotton 6kgting.
Red-indicates that the drying cycle has starbetter to only drted.y small loads (i.e half fill drum).
Amber-indicates that the clothes are nearly dry. This If the cut-out continues to operate after checking the abo(for minimum creasing 2kg)ve
will illuminate approx. 10-12 minutes befIt is better to drore y small and large articles together.points, you should contact your service agent.Delicates 2kg
the end of the drying cycle.
We suggest a fabric conditioner to be used to reduce static� Check that you have selected the correct dryness setting.
Green-indicates that the clothes are ready to be
For electrical ratings see plate on back of dryer.
removed from the dryer.electricity.
If your machine does not workcheck the following before calling
Flashing Green- indicates that Anti crease is in operation and For Model No. see serial plate inside door (needed when
Do not overload the dryer or dry large bulky items such asa service engineer:
that the clothes are ready to be removed from requesting service).
duvets or sleeping bags as it is important that the airflow through� Check that there is a supply of electricity.
the dryer.
Room temperature range 5uC to 30uC.
E. START BUTTON: To start the drying cycle.the dryer is not obstructed.� Check that the door has been properly closed and the
F. NEON (IF �BO IS NOT FITTED): This neon will light when themachine is switched on.Your washing machine should have a spin speed of not less
Do not place items contaminated with inflammable substances
dryer has started, and will flash when the programme reachesthan 800rpm.
in the dryer, such as petrol, cleaning solvents, cooking oil, fat, or� Check that the water bottle has been withdrawn from, and
the anti-creasing stage.
replaced into the machine.The �dryO setting was used to rate the energy efficiency of this
There are no Heat or Timer settings on these models.hair lacquer.These can cause fires. For the same reason, do not
appliance.
Check care labels inside the garments.dry rubber, foam rubber, plastic or paper.� Check the plug internal connections. |