Inserting the Battery into the
!When setting up your television, select a location
where as little light as possible falls on the screen.Remote Control Handset
!The ideal viewing distance is five times the diagonal
1Insert the battery supplied. Make sure it is inserted
width of the screen.
correctly (markings in the battery compartment).
!If the television is to be built into a compartment or
!When the battery is dead, the message
similarly enclosed, minimum distances must be
�BATTERY� appears on the picture screen.
maintained.
Remove the dead battery immediately.
1010
cmcmWe assume no responsibility for damage resulting
from battery leakage.
2020 cm
cm
Dead batteries must be disposed of properly.
Connecting the TV Set
Safety and Installation
1Insert the plug of the aerial lead into the aerial
socket of the TV set.
2Insert the plug of the mains lead into a wall outlet.
!Do not cover the ventilation openings on the back.
!The heat exchange inside the unit generates an air
Switching the TV Set On/Off
circulation which attracts dust particles (carpet and
curtain fibres and home dust). These particles
1Press the cIO button on the unit.
accumulate inside the ventilation slots obstructing
these over the years and causing a build-up of heat.!If you do not use the TV set for extended periods of
Heat build-up can reduce the service life of yourtime (e.g. at night), turn it off with this button.
television, and can also be dangerous.
This helps you to save energy.
For your own safety, let remove the dust deposits
by a specialist from time to time.
!Never set up speakers next to the unit.The dialogue line as userOs guide
!When setting up and using this unit, please make
sure that the mains connection wire is free and not!The line which is displayed at the bottom of the
jammed in order to avoid damage.menus shows you which buttons on the remote
!Never place the television near heat sources.control handset are to be used to change settings..
!Even if your television is switched off, it can still beThe >, <, , signs on the picture screen are
damaged by lightning striking the mains and/orsymbols for the following buttons on the remote
aerial cables.control handset:
For this reason, you should always disconnect your
, = P+ and P� buttons. Cursor movement
television from the mains and the aerial system
up/down for function selection.
during electrical storms.
<, >= � and + buttons: Cursor move-
!Never expose the unit to moisture.
ment left/right for function selection.
!Do not insert foreign objects into the ventilation
In the following text, the buttons instead of the
openings on the back.
symbols will be shown.
Caution! High voltage!
Additional Information for Units sold in Great Britainplug is used it must be protected by a 5 Amp fuse either in the plug or at the dis-
tribution board.
Units sold in GB are suitable for operation from a 240 V AC, 50 Hz mains supply.
Important:
In case this appliance is supplied with a Safety Standard Approved mains lead fit-The wires in the mains lead are coloured in accordance with the follow-ing code:
ted with a non-rewireable 13 Amp mains plug which, if unsuitable for your
socket, should be cut off and an appropriate plug fitted by aBLUE� NEUTRAL
qualified electrician. The fuse and fuse holder must be removed from the plug asBROWN� LIVE
accidental insertion of the redundant plug into a 13 Amp socket is likely to cause
an electrical hazard.As the colours of the wires in the mains lead of your appliance may not corre-
spond with the coloured marking identifying the terminals in your plug, proceed
Note: The severed plug must be destroyed to avoid a possible shock hazardas follows:
should it be inserted into a 13 Amp socket elsewhere.Connect the BLUE coloured wire to plug terminal marked with the letter "N" or
coloured black.
If it is necessary to change the fuse in the non-rewireable plug, the correct type
Connect the BROWN coloured wire to the plug terminal marked with a letter "L" or
and rating (5 Amp ASTA or BSI approved BS 1362) must be used and the fuse
coloured red.
cover must be refitted. If the fuse cover is lost or damaged the lead and plug must
In no circumstance must any of the wires be connected to the terminal marked
not be used until a replacement is obtained. Replacement fuse covers should be
with a letter "E", earth symbol , coloured green or green and yellow.
obtained from your dealer.
Replacement mains lead can be obtained from your dealer.
If a non-rewireable plug or a rewireable 13 Amp (BS 1363) plug is used, it must
be fitted with a 5 Amp ASTA or BSI approved BS 1362 fuse. If any othe type of
2 |
ACEC
