AV NETWORK SETUP WIZARD
SETUP PROCEDURE USING AV NETWORK DEVICE CODES:
An AV Receiver Setup example is shown below. If your device is not listed or the device codes not work after following the setup
procedure, please refer to the AV NET Learning wizard procedure on pages 33-34.
1. Press the A/V Net button on the remote control.10. If ?OK? was selected, and the 4 digit code was invalid, the
screen below appears, then goes back to the Device
DVDPOWERMENUHOMECode entry screen.
DVD2
VCR
VCR2ATTENTION
Find your AVR
4-digit manufacturers code
AV Receiverand enter it here
MoveSELSelect
FIRST TIME USE
2. Use CURSOR PADS or to highlight Device Setup.
3. Press the SELECT button or CURSOR PADS on the 11. Repeat Device Setup procedure until the Source (SRC)
remote control and the device selection screen appears.Setting Screen appears.
PV RecorderThis screen allows you to assign a label for each Source (SRC1
Cable Boxto SRC8) connection on the AV Receiver. Depending on the
Set Top Boxnumber of source connections to the AV Receiver, some sources
may not be available.
Custom
12. To label your sources, use CURSOR PAD or to
Device Setup
highlight SRC1.
MoveSELSelect13. Use CURSOR PAD or to select the Source (DVD,
DVD2, VCR, VCR2, PVR, CBL, STB, TV or Custom). If
SRC1 is active, video and audio will be available depending
4. Use the CURSOR PADS or to choose AV Receiver on the connections.
and press the SELECT button on the remote control.14. Repeat for SRC2 to SRC8 if applicable.
5. The Setup button on the bottom of the screen becomes 15. Select DONE to continue.
highlighted. Press the SELECTbutton on the remote control
HITACHI AV NET SET UP
to enter the setup screen.
AV Receiver (SRC Setting)
SRC1SRC1
HITACHI AV NET SET UPSRC2SRC2
SRC3SRC3
Please choose the device to set up.SRC4SRC4
SRC5SRC5
( ) DVD( ) Set Top BoxSRC6SRC6
( ) DVD2( ) DVD3 (Custom)SRC7SRC7
( ) VCR( ) VCR3 (Custom)SRC8SRC8
( ) VCR2( ) PVR2 (Custom)
( ) AV Receiver( ) CBL2 (Custom)BACKDONEEXIT
( ) PV Recorder( ) STB2 (Custom)
( ) Cable BoxListMoveSet InputSELIR Out
BACKSETUPMODIFY
16. Select CONTINUE to setup another device.
MoveSELSelect
HITACHI AV NET SET UP
6. Using the remote, enter the four digit Device Code for your
Congratulations!
equipment, found on page 25.Your AVR is now connected
7. Use the CURSOR PAD to select AV Input. Press the to your AV network.
CURSOR PAD or to set the INPUT to which your Would you like to set upanother device?
device is connected.
8. Use the CURSOR PAD to select Internal Speakers. DoneContinue
Speakers to ON or OFF, then press SELECT to set the
option chosen.
9. Press CURSOR PAD to select Transmission Test. Press Move
SELSelect
the CURSOR PADS or to select Power, Play, or CH UP
softkeys, before pressing the SELECT button to perform a
17. Select DONE to finish and the screen below appears to
Transmission Test of the softkey selected. If the device
show the device(s) which has been set-up.
responds, then it is properly set up. Select OK. (If the
Transmission Test failed, try another code).HITACHI AV NET SET UP
HITACHI AV NET SET UPDeviceCodeVideoAudio
AV ReceiverDVD----Not SetupNot Setup
DVD2----Not SetupNot Setup
Device Code- - - -VCR----Not SetupNot Setup
VCR2----Not SetupNot Setup
(Enter Code O9999� to uninstall)AVR1360Not SetupNot Setup
AV InputInput4PVR----Not SetupNot Setup
CBL----Not SetupNot Setup
Internal Speakers
STB----Not SetupNot Setup
OnOffSTB2----Not SetupNot Setup
Transmission TestPOWERPLAYCH UP
BACKOKEXIT
EXITSELSelect
Move0-9Input
18. Select EXIT to quit.
24 |
ACEC
