Remote Programming 11
VCR setup
The remote control is programmed with VCR codes for power on, power off, play, stop, fast-forward,
rewind, channel up, and channel down operation.
1) Find the VCR brand from the list of codes shown below.
2) Slide the 2-way selector switch to OTV�.
3) Press and hold down the DISPLAY button.
4) With the DISPLAY button held down, enter the first code number listed with the 10 key pad.
5) Release the DISPLAY button.
6) Confirm the operation of the VCR.
Y If your VCR does not respond to the first code, try the others listed. If it does not respond to any code,
try the Search Codes Function at the bottom of the page.
Y Some manufacturerOs VCROs may not respond to the TV/VCR button, even if other buttons work properly.
Y To record, hold down the REC button on the remote and press PLAY.
Y RM-C205 Users:The model RM-C205 remote control can only be used with JVC-brand VCROs.
VCRsCODESVCRsCODESVCRsCODES
Admiral035Magnavox031, 023, 024, 086Samsung037, 060, 062, 033, 089
Aiwa027, 032Marantz003, 004, 005Sansui003, 026, 020, 052
Akai029, 072, 073, 074Marta064Sanyo063, 067, 091, 071
Audio Dynamic003, 005Memorex024, 067Scott059, 060, 062, 067, 038, 040,
Bell &Howell063, 071MGA038, 040, 047, 048, 041, 042047, 048, 026, 020
Broksonic020, 026Minolta058, 045Sears063, 064, 065, 066, 058, 000,
Canon023, 025Mitsubishi038, 040, 047, 048, 041, 042,001
CCE043078, 090Shintom075
Citizen064Multitech047, 027, 062Sharp035, 036, 080, 088
Craig063, 029, 064NEC003, 004, 005, 000Signature 2000027, 035
Curtis Mathes045, 024, 027, 093Olympic024, 023Singer075
Daewoo043, 059, 024, 092Optimus028, 021, 035, 064Sony028, 029, 030, 053, 054, 055
DBX003, 004, 005Orion026, 020SV2000027
Dimensia045Panasonic023, 024, 021, 022Sylvania031, 023, 024, 027
Emerson043, 026, 077, 061, 025, 042,Penney024, 058, 045, 063, 003, 004,Symphonic027, 081
020, 076005, 093Tashiro064
Fisher063, 066, 067, 065, 071Pentax058, 005, 045, 093Tatung003, 004, 005
Funai027, 026, 020, 000Philco031, 024, 027, 023, 026, 020,Teac003, 004, 027, 005
GE033, 045, 024, 093043Technics021, 022, 023, 024
Go Video037, 051, 049, 050, 089Philips031, 023, 024, 086Teknika024, 027, 070
Goldstar064Pioneer023Toshiba059, 046, 079
Gradiente083, 084, 081, 000, 001Proscan045, 058, 023, 024, 031, 046,Vector Research005
Hitachi023, 045, 058, 027, 081, 093059, 060, 033, 087, 093Wards035, 036, 067, 044, 064
Instant Replay024, 023Quasar021, 022, 023, 024Yamaha063, 003, 004, 005
Jensen003Radio Shack033, 024, 063, 036, 067, 040,Zenith044, 082, 064
JVC000, 001, 002, 003, 004, 005027
Kenwood003, 004, 064, 005RCA033, 045, 058, 023, 024, 031,
LXI027, 064, 058, 065, 066, 063,046, 059, 060, 083, 085, 087,
067093
Realistic024, 063, 036, 067, 040, 027
Search Codes Function:
1) Slide the 2-Way Mode Selector switch to TV.
2) Press the VCR POWER and RETURN+ buttons. Hold for at least three seconds and release.
3) Press VCR POWER, see if the VCR responds.
4) If there was a response, press RETURN+. The operating codes are now set. If there was no response,
repeat Step 3. If you repeat Step 3 more than 80 times without a response, use the remote control which
came with the VCR. |
ACEC
