Troubleshooting
If a problem occurs when you are using the TV, check the below
troubleshooting guide before calling for repair.
Y Colour patches appear Y This may due to the magnetized device such as a
at the corner of thespeaker near to your TV. Keep the device apart from
Y No picture,Y Deactivate the BLUE BACK function if it is turned on.screenyour TV. Alternately, you can also use the magnetic-
no soundY Choose the appropriate sound system. Refer to
shielded speaker.
OSOUND SYSTEM� on page 13.
Y Image takes a shortY Image required time to stabilize before display. This
Y Snowy pictureY Check the aerial cable and its connection with the TV.
period to be displayedis not a malfunction.
Y Stripes appear on the Y Interference occurs caused by other devices such asY TV may emittedY This is due to a sudden change in temperature and it is
picturean amplifier, personal computer, or a hair drier. Move
crackling soundnot a malfunction. If the crackling sound is too frequent,
such devices away from your TV.request your service technician for inspection.
Y Double-picturesY Interference occurs caused by signal reflecting from
Y Feel a slight electricY This is due to the static electricity of the picture tube
(ghosting) occurmountains or building. Try to adjust the aerialOsshock when touchingand it will not harm the human body. This is not a
direction or use a better directionality antenna.
the TV screenmalfunction.
Y Poor pictureY Choose the appropriate colour system. Refer toY After you connect the Y Please check that the AUTO SIGNAL DETECT
OCOLOUR SYSTEM� on page 9.
signal to VIDEO-2 andfunction is on or off.
Y Adjust the COLOUR or BRIGHT setting. Refer toplayback VCR or DVD Y Press button (VCR or DVD Player) to turn the
OPICTURE SETTING� on page 10.
Player, the Auto Detect machine off and turn it on again; do not turn the
Y White and bright still Y Inevitable phenomenon due to the nature of thedoes not work.machine off and on suddenly.
image look as if itpicture tube. This is not a malfunction.Y Inspect the video cable connection on VIDEO-2 that
were colouredthey are connected properly.
Y Top of the image from Y This is due to the condition of the video signalY When you are watching Y Inspect the video cable connection on VIDEO-2 that
software products orwhereby the image was not recorded properly. Thisanother channel that is they are connected properly.
video tape is distorted is not a malfunction.not VIDEO-2, AUTOY In a certain VCR or DVD Player, the function might
SIGNAL DETECToperate by the discontinuity of the signal.
Y Poor soundY Adjust the sound frequency properly. Refer to
OEQUALIZER� on page 14.works while VCR or
DVD Player was on.
Y Stereo or bilingualY TV channel reception is poor. Change the stereo/
sound is unclearbilingual mode to mono sound (see page 14).Y While you are watching Y In a certain VCR or DVD Player, the function might
TV on the otheroperate by the discontinuity of the signal.
Y Cannot operate the Y The batteries may be exhausted. Replace with newchannels, AUTO SIGNAL
remote controlbatteries (see page 7).DETECT works when
Y Ensure that you are operating the remote less thanyou press 1,7,3, !
seven meters from the front of your TV.or 8 on the front panel of
Y Cannot operate the Y Press TV/VIDEO button to return to TV mode and tryVCR or DVD Player.
menusoperating the menus.Y After TV was on, AUTO Y Video signal from VCR or DVD Player cause the
Y Cannot operate theY Deactivate the CHILD LOCK function if it is turned onSIGNAL DETECTfunction runs properly to indicate that there are video
front control buttons(see page 16).works.signal on VIDEO-2 channel.
22
GGT0097-001A-H-EN2219/05/2005, 9:00 AM |
ACEC
