Settings & Controls for Recording
Selecting & Confirming Input SignalsSetting the Encoding Format for Audio & Video
The selection of audio and video input signals is carried out from the INPUT SELECT MENU screen as described below. InThe setting of encoding formats for audio and video is carried out from the RECORDER MENU (1/2) screen as described below.
addition, the type of input signals that have been selected can be confirmed on the front panel.
Video input indicatorsBUSY
Selecting Input SignalsSetting Encoding Formats
BUSYOPEN/CLOSE
OPEN/CLOSE
Stop the DVD recorder.Stop the DVD recorder.
OPTIONDV Y/CLINE
1.Open the INPUT SELECT MENU screen.SET UP1.Open the RECORDER MENU (1/2) screen.
OPTIONDV Y/CLINESET UP button
SET UPq Press the SET UP button to display the Setup Menu.q Press the SET UP button to display the Setup Menu.
SET UP buttonw Select INPUT SELECT using the 6 and 7 buttons and then press theMENUTOPMENUw Select RECORDER using the 6and7buttons and then press the SETSET
MENUTOPMENUSETSET button.button.
SET button
SET button2.Make the required settings on the INPUT SELECT MENU screen.2.Make the required settings on the RECORDER MENU (1/2)
q Select the parameter to be set using the 6 and 7 buttons, and thenRECORDER MENU (1/2) screenscreen.
INPUT SELECT MENU screenpress the SET button to display a list of possible settings.RECORDER MENU (1/2)q Select the parameter to be set using the 6 and 7 buttons, and then
w Select the required setting using the 6 and 7 buttons, and then pressMENUpress the SET button to display a list of possible settings.
INPUT SELECT MENU
the SET button to adopt this setting. CHAPTER CREATIONMANUALw Select the required setting using the 6 and 7 buttons, and then press
MENU SET INTERVALEvery05Min
INPUT SELECTLINETOTAL CONTENTS TIMENO USEthe SET button to adopt it.
3.Complete the setting process. ENCODE QUALITY (Mbps)4.4
To do so, carry out one of the following procedures. AUDIO ENCODELPCMAUTO3.Complete the setting process. ASPECT
? Select MENU and press the SET button to return to the Setup Menu.To do so, carry out one of the following procedures.
? Press the SET UP button to return to the normal screen display.? Select MENU and press the SET button to return to the Setup Menu.
? Press the SET UP button to return to the normal screen display.
ItemDescriptionVideo Encoding
INPUT SELECTThis parameter is used to select the audio and video input signals.
LINE : The composite video signal from the VIDEO LINE IN terminal and the analog audio signalsItemDescription
from the AUDIO IN terminals are to be used.
Y/C : The YC separate signal from the Y/C IN terminal and the analog audio signals from theTOTAL CONTENTS TIMEIf you already know the duration of the video to be recorded, this parameter can be set to the
AUDIO IN terminals are to be used.corresponding time to allow your BD-X200 to select the optimum encoding bit rate. (Make a setting
DV: The audio and video signals from the DV IN/OUT terminal are to be used.in hours and minutes.)
I If the recording time is set using this parameter, ENCODE QUALITY will be set automatically,
and this setting may not be modified manually.
NoteI If this function is not to be used, set it to NO USE.
Setting of INPUT SELECT will not be possible when REMOTE SELECT from the REMOTE MENU screen has been set to
When this setting is made, ENCODE QUALITY will be returned to its previous setting.
DV(MASTER), DV(SLAVE), or DV(TRIGGER).
DV signals will be used for input at these times.ENCODE QUALITY (Mbps) This parameter can be set when TOTAL CONTENTS TIME has been set to NO USE.
Specifically, it allows direct setting of the encoding bit rate (i.e., the amount of data per second).
Large values increase the quality of the video; however, this also increases the overall data size.
Setting range:
Confirming Input SignalsThe range of values that can be set depends on the audio encoding format.
LPCM: 4.0 to 7.8 Mbps (in 0.2 Mbps steps)
DOLBY DIGITAL: 2.0 to 9.0 Mbps (in 0.2 Mbps steps)
The type of video signals that have been selected for input can be confirmed
using the video input signal indicators on the DVD recorders front panel.
OPTION DV Y/C LINE
Specifically, the indicator corresponding to the type of input signal selected
using INPUT SELECT will be lit up or flashing.
Lit: The selected signal is being received.
Flashing : The selected signal is not being received.
3233 |
ACEC
