For servicing
? See the service manual page 1-10 O1.6 SERVICE MENU�.
3 CONNECTIONS4 MENU SWITCHES
5Edit adjust settingYou can set menu switches using either the on-screen display or the counter display. To set switches on the on-screen display,
The No. 353 <EDIT ADJUST> menu switch must be adjusted according to the configuration of the editing system beingyou will need to connect a monitor to the VCROs [VIDEO MONITOR OUT] connector. This section explains how to set switches
used.using the on-screen display. The same procedures apply to switch setting on the counter display, the only difference being that
each menu switch item is indicated by numeric code rather than by name.
Setting table (when the RM-G800 is used)
Signal connection methodPlayerSettingRecorderSetting4-1 Menu switch organization
AnalogBR-DV6000 FBR-DV6004 FOn-screen display
IEEE 1394BR-DV6000 FBR-DV6002 F
AnalogBR-DV6000 FBR-S800---
Menu switch group select screen
AnalogBR-DV6000 FSR-S365 (U MODEL)---
SR-S388 (E MODEL)STOP[SET]Pressing the [MENU] button with the normal screen
TCR 12:00:00:00
AnalogBR-S800/BR-S500 (+ SA-N50)*---BR-DV6003 Fdisplayed brings up the menu switch group select screen.
Select the desired group with the [SHIFT +/�] button.
[MENU]
* To ensure the stability of input signals, install the SA-N50 in the BR-DV600.The selected group number blinks.
Menu switch group select screen
Press the [SELECT] button to go to the selected group
000: SERVO/SYSTEMmenu switch setting screen.
100: VIDEOMenu switch setting screen
200: AUDIO
300: SYSTEM400: TIME CODE
[SHIFT]
5Non-linear editing system5HM: HOUR METER002:OPERATION LOCK00: ONSCREEN
Menu switch setting screen
Material recorded on a MiniDV tape can be captured to a non-linear editing system. The following non-linear editingOFF003:SYNC SELECT
systems are able to utilize Super Scene Finder (SSF) data.AU050:REMOTE SELECTTOTo access this screen, press the [SELECT] button on the
Y Canopus Corporation: DV Rex RTJVC BUS+RS422Amenu switch group select screen.
Y CasablancaPress the [MENU] button to go to the menu switch group
Audio signalselect screen.
108:VIDEO INPUT SELECT
Video signalLINE
IN/OUTDV
LINEVIDEOCOMPONENTAUDIO[SELECT][MENU]
Y/CCH 1/3INININCH 2/4PGZ01945
R-YB-Y
YOUT(HOUR METER)Menu switch setting procedure
MONITOROUTOUTOUTDH :DRUM HOUR METER000000H1Press the [SHIFT �/+] button on the menu switch set-
MONITOROUTSYNC INTIME CODESERIAL1REMOTE2ting screen to select the menu switch you want to set.
TIMERSPARE
RECPLAYDC 12VOFF[The selected menu switch number blinks.
2Press the [SELECT] button to change the set value.
On-screen displayCounter display3Repeat steps 1 and 2 to change any other menu switches.
When entered4Press the [SET] button to end menu switch setting.
[The set value is entered and the normal screen is
Remote controlrestored. When entering the data, the indications shown
DATA SET
Non-linear editing systemon the left are displayed. If data has not been entered
and menu switch setting is ended, OAbort� indication is
5Control via the DV connectorshown.
Y When the DV connector is used for control, assemble editing cannot be performed.When data has not
To access another group menu switch setting screen without
Y When the VCR is stopped via the DV connector, a command error message may be returned to the controller. This is notbeen entered yetending menu switch setting, press the [MENU] button.
a malfunction.ABORT
Notes on connecting a cable to the [DV IN/OUT] connectorMenu switch setting screen
Set the following menu switches, turn the connected equipment ON and then connect the cable to the [DVSwitching the002:OPERATION LOCKOFF
IN/OUT] connector. (If two BR-DV600s are connected to each other, it is not necessary to turn them ON.)setting screen[SHIFT] +/�: Item select003:SYNC SELECTAUTO[MENU]
Menu switch settingsMENU ADVANCE PRESET[SHIFT]050:REMOTESELECTJVC BUS+RS422A[SELECT]
Y When used as a player
Set the No. 108 <VIDEO INPUT SELECT> menu switch to any position except OIEEE 1394�.0SHIFTSHIFTCH 1/3OVERAUTO OFFDEW
HOLDSHIFTA. DUB40302010dB
(If this switch is currently set to OIEEE 1394�, change the setting and turn the power OFF and ON again.)CH 2/4OVERSERVO RF[SET]
Y When used as a recorderSELECTAUDLOCK32k48kPB NDFHOLD
SET000~ : SERVO/SYSTEM
Set the No. 108 <VIDEO INPUT SELECT> menu switch to OIEEE 1394�.MENU100~:VIDEO
MONITOR OUTPUT COUNTERHMSF200~:AUDIO
Y When controlled by another device via the [DV INPUT] connectorLCH-1/2CTL300~ : SYSTEM400~ :TIME CODE
Set the No. 050 <REMOTE SELECT> menu switch to OIEEE 1394�.MIXMIXTC[MENU]500~ : ONSCREEN
RCH-3/4UBHM: HOUR METER
AUDIOSTOP
Menu switch displayTCR 12:00:00:00
SELECT: Changes the setting.Menu switch group
SET:Enters the setting.select screen
1617 |
ACEC
