English
4ONLY FOR OPRO LOGIC�Enjoying Playback with Dolby Surround
DELAY TIME
Press DELAY TIME repeatedly to select
You can use the settings you have already stored in memory.
the proper delay time of the rear speaker
output.On the unit:On the unit:
Y Each time you press the button, the delay time changes as
follows.PRO LOGIC
/ 3 STEREO
1Press PRO LOGIC/3 STEREO c button to
DELAY1DELAY2
select the Dolby Surround mode you want.
DELAY4DELAY3
The PRO LOGIC or 3 STEREO indicator lights up
DELAY1: Select this when the distance from you to your rearon the display.
(15 m Sec)speakers is greater than that to the front speakers.
DELAY2: Select this when the distance from you to your rearPRO LOGIC3 STEREO
(20 m Sec)speakers is almost equal to that to the front speakers.
DELAY3: Select this when the distance from you to your rearRA
PR
(25 m Sec)speakers is less than that to the front speakers.RA
DELAY4: Select this when the distance from you to your rear
Y Each time you press the button, the Dolby Surround modes
(30 m Sec)speakers is much less than that to the front speakers.
changes as follows:
TEST TONEPRO LOGIC3 STEREO
5Press TEST TONE to check the speaker
Cancelled
output balance.
A test tone comes out of the speakers in the followingY When Dolby Surround is activated, the sound mode is
order:cancelled temporarily.
LEFT
CENTER
*
(Left front speaker)(Center speaker)
2Select and play a sound source encoded with Dolby
SURROUND
RIGHT
(Rear speakers)(Right front speaker)Surround. (with the DOLBY SURROUND mark).
* OCENTER� does not appear when selecting OPHANTOM�
To cancel the Dolby Surround mode, press PRO LOGIC /
or OOFF� for the center mode, and no test tone comes out of
3 STEREO repeatedly until neither PRO LOGIC nor
the center speaker.
3 STEREO indicator remains lit on the display.
6Press VOLUME + / � a to adjust the
On the remote control:On the remote control:
test tone volume to a proper level.
SHIFT
1Press and hold SHIFT 9 until the following
procedure is finished.
7If necessary, adjust the speaker output balance so
that the output level from center and rear speakers2Press PRO LOGIC or 3 STEREOPRO LOGIC3 STEREO
is almost equal to that from the front speakers:
c whichever you want to use.
The PRO LOGIC or 3 STEREO indicator
To adjust the center speaker output�CENTER
LEVEL +lights up on the display.
level (from �10 to +10), press CENTER
LEVEL � / +.Y When Dolby Surround is activated, the sound mode is
Y You cannot adjust the center speaker output levelcancelled temporarily.
when you select OPHANTOM� or OOFF� for the center mode.
3Select and play a sound source encoded with Dolby
To adjust the rear speaker output level�REAR
LEVEL +
Surround. (with the DOLBY SURROUND mark).
(from �10 to +10), press REAR LEVEL � / +.
Y You cannot adjust the right and left speaker
To cancel the Dolby Surround mode, press PRO LOGIC
output levels separately.
or 3 STEREO (the same button you have pressed to activate Dolby
Y You cannot adjust the rear speaker output level
Surround in step 1 above) so that neither PRO LOGIC nor 3 STEREO
when using Dolby 3 Stereo.
indicator remains lit on the display.
TEST TONE
8Press TEST TONE again to stop the test
* Manufactured under license from Dolby Laboratories
tone.Licensing Corporation. DOLBY, the double-D symbol, and
OPRO LOGIC� are trademarks of Dolby Laboratories
Licensing Corporation.
9Release SHIFT 9.
20
EN18-20;MX-J777V/PM6207/8/99, 9:13 AM |
ACEC
