DLA-G150CLU / LCT1123-001B / ENGLISH
DLA-G150CLU&CLE_Eng.book Page 3 Thursday, February 21, 2002 2:39 PM
- This product should be operated only with the type of - When connecting other products such as VCR?s, and
power source indicated on the label. If you are not sure personal computers, you should turn off the power of this
of the type of power supply to your home, consult your product for protection against electric shock.
product dealer or local power company.- Do not place combustibles behind the cooling fan. For
- This product is equipped with a three-wire plug. This example, cloth, paper, matches, aerosol cans or gas
plug will fit only into a grounded power outlet. If you are lighters that present special hazards when over heated.
unable to insert the plug into the outlet, contact your
- Do not look into the projection lens while the illumination
electrician to install the proper outlet. Do not defeat the
lamp is turned on. Exposure of your eyes to the strong
safety purpose of the grounded plug.light can result in impaired eyesight.
- Power-supply cords should be routed so that they are not
- Do not look into the inside of this unit through vents
likely to be walked on or pinched by items placed upon or (ventilation holes), etc. Do not look at the illumination
against them. Pay particular attention to cords at doors,
lamp directly by opening the cabinet while the
plugs, receptacles, and the point where they exit from the
illumination lamp is turned on. The illumination lamp also
product.contains ultraviolet rays and the light is so powerful that
- For added protection of this product during a lightning your eyesight can be impaired.
storm, or when it is left unattended and unused for long - Do not drop, hit, or damage the light-source lamp (lamp
periods of time, unplug it from the wall outlet and unit) in any way. It may cause the light-source lamp to
disconnect the cable system. This will prevent damage
break and lead to injuries. Do not use a damaged light-
to the product due to lightning and power line surges.
source lamp. If the light-source lamp is broken, ask your
- Do not overload wall outlets, extension cords, or dealer to repair it. Fragments from a broken light-source
convenience receptacles on other equipment as this can lamp may cause injures.
result in a risk of fire or electric shock.- Xenon gas is enclosed with high pressure inside the light-
- Never push objects of any kind into this product through source lamp (lamp unit) of this projector. If you drop or
openings as they may touch dangerous voltage points or impart a shock to the lamp, or discard it as is, there is the
short out parts that could result in a fire or electric shock. possibility of explosion, leading to personal injury. Use
Never spill liquid of any kind on the product.special care when handling the lamp. For any unclear
- Do not attempt to service this product yourself as points, consult your product dealer.
opening or removing covers may expose you to - Do not ?ceiling-mount? the projector to a place which
dangerous voltages and other hazards. Refer all service tends to vibrate; otherwise, the attaching fixture of the
to qualified service personnel.projector could be broken by the vibration, possibly
causing it to fall or overturn, which could lead to personal
- Unplug this product from the wall outlet and refer service
to qualified service personnel under the following injury.
conditions:- Use only the accessory cord designed for this product to
a) When the power supply cord or plug is damaged.prevent shock.
The power supply voltage rating of this product is
b) If liquid has been spilled, or objects have fallen on the
product.AC 120 V, the power cord attached conforms to the
following power supply voltage. Use only the power cord
c) If the product has been exposed to rain or water.designated by our dealer to ensure Safety and EMC.
ENGLISH
d) If the product does not operate normally by following
When it is used by other power supply voltage, power
the operating instructions. Adjust only those controls cable must be changed.
that are covered by the Operation Manual, as an
improper adjustment of controls may result in damage Ensure that the power cable used for the projector is the
AIScorrect type for the AC outlet in your country.
and will often require extensive work by a qualified �
technician to restore the product to normal operation.Consult your product dealer.
e) If the product has been dropped or damaged in any
FRANPower cord
way.
f ) When the product exhibits a distinct change in
performance - this indicates a need for service.
- When replacement parts are required, be sure the Power supply voltage: AC 120 V
service technician has used replacement parts specified
by the manufacturer or with same characteristics as the
original part. Unauthorized substitutions may result in
* DO NOT allow any unqualified person to
fire, electric shock, or other hazards.
install the unit.
- Upon completion of any service or repairs to this product,
Be sure to ask your dealer to install the unit (eg.
ask the service technician to perform safety checks to
determine that the product is in proper operating attaching it to the ceilling) since special technical
knowledge and skills are required for installation.
condition.
If installation is performed by an unqualified person, it
- The product should be placed more than one foot away may cause personal injury or electrical shock.
from heat sources such as radiators, heat registers,
stoves, and other products (including amplifiers) that
produce heat.
3 |
ACEC
