Controls and Features Controls and Features
Bottom SurfaceControl Panel on the Projector
UPDOWN
ESCAPEPRESETKEYSTOENTERNEVOVIDEOLMENULUMEHIDEPCAMPTEMPSTAND BYOPERATEt1
r
LAMPTEMPSTAND BY
eOPERATE2
HIDE3
yw
PC4
qKEYSTONEVOLUME
uVIDEO5
PRESETMENU
ip6
97
ESCAPEENTER
o8
yAir inlet (filter)
1STAND BY Indicator
Air is taken in through the filter to cool the light-source Memo
ON: When in stand-by mode.
lamp. If the filter is blocked or if something that obstructs While in the cool-down mode (STAND BY indicator is blinking):
Blinking: When in cool-down mode.
the flow of air is placed around the projector, heat may Even if you press the OPERATE button, the projector is not
build up inside and could cause a fire. For required Memoturned on. Wait until the projector enters stand-by mode
space, refer ?Preto cautions for Instal? onlation page 15.(STAND BY indicator stays lit).
About the cool-down mode:
CAUTIONThis projector has a function to cool down the heated la4PC buttmp for a on
fixed period of time (approx. 120 seconds) after projection Use this button tois select a device connected to the PC 1
Be careful as paper, cloth or soft cushion could be drawn in finished. This feature is referred to as the cool-down or PC 2 mode.terminals. Each time you press the button, the
if placed nearby. Do not block the filter, or heat may build The purpose of the cool-down mode is to prevent innseleer parts ction alternates between PC 1 and PC 2.
up and could cause a fire.from being deformed or broken by heat from the heate*d lamp ?PC1? or ?PC2? will be displayed on the top right of the
Clean the filter periodically. For de?Cleantails, ing refer to as well as to prolong the life of the lamp.projected image. (This function can be disabled by the
and Replacing the Filter ? onCo verpage 60. Deposition of menu.)
dirt on the filter reduces the cooling effect, causing heat to CAUTIONS
5VIDEO button
build up inside, which could cause a fire or malfunction.
Do not turn off the MAIN POWER switch while in the Use this button to cool-select a device such as a video deck
ENGLISH
uOpening for replacing the light-source lampdown mode.connected to the AV IN (Y/C or VIDEO) terminal of the
For replacing the light-source lamp, refer to ?Replacing Do not place the projector on its side or stand it projupector. Each time you press thright e button, the selection
the Light-Source ?L on pagampe 56.while in the cool-down mode; this may block the vents.alternates between Y/C and VIDEO.
*?Y/C? or ?VIDEO? will be displayed on the top right of the
iFixing foot2OPERATE indicatorprojected image. (This function can be disabled by the menu.)
oPosition selecting screw for ceiling mountingON : When the projector is in operation (pro6jectingMENU button).
When using the projector in an upside-down, ceiling-OFF : When the projector is not in operation (not Use this button to enter or exit the menu mode. The DEUTSHmain
projecting).
mounted position (inverted top-to-bottom and right-to-menu appears or disappears at the screen. For details,
left), the ?position selecting screw for ceiling mounting? 3OPERATE buttonrefer to?Basic Menu Operatio? on pagne 42.
must be turned to switch to ceiling mounting.When the projector is in the stand-by mode, press this
7ENTER button
This will correct variance in color images (shading), button one second or more, and the projector is turned AIS
which otherwise would occur in ceiling mounting.This button will be used in the menu mode. Use to �on, causing the OPERATE indicator to light.
For more information, refer to ?Setting the Position Press it one second or more again, and the projector display the hierarchical menus. Also use whe?ENTER ? n
is displayed against the item on the menu screen or
Selecting Screw for Ceiling ? on pageMounting21.goes into the cool-down mode, then stand-by mode.
when the ?All reset? selection is confirmed. For detaiFRANls,
(Refer to page 31.)
CAUTION*You cannot use the OPERATE button for about one refer to?Basic Menu Operatio? on pagne 42.
To ceiling-mount and adjust the projector, special expertise minute after the lamp blinks. Press the button 8 after Cursor ba uttons5/ /2/3
and technique are necessary. Be sure to ask your dealer or minute or longer has elapsed.These buttons will be used in the menu mode to select an
specialist to perform this work.item, or to set or adjust the value. For details, refer to
?Basic Menu Operatio? onn page 42.
ITALIANO
OL
N
ESPA
89 |
ACEC
