Safety Precaution
Y Slots and openings in the cabinet are provided for ventila-Y The product should be placed more than one foot away from
tion. These ensure reliable operation of the product and pro-heat sources such as radiators, heat registers, stoves, and
tect it from overheating. These openings must not be blockedother products (including amplifiers) that produce heat.
or covered. (The openings should never be blocked by plac-
Y When connecting other products such as VCROs, and per-
ing the product on bed, sofa,rug, or similar surface. It should
sonal computers, you should turn off the power of this prod-
not be placed in a built-in installation such as a bookcase or
uct for protection against electric shock.
rack unless proper ventilation is provided and the manufac-
turerOs instructions have been adhered to.)Y Do not place combustibles behind the cooling fan. For exam-
For proper ventilation, separate the product from other equip-ple, cloth, paper, matches, aerosol cans or gas lighters that
ment, which may prevent ventilation and keep a distance ofpresent special hazards when over heated.
more than 11-7/8� (30 cm).
Y Do not look into the projection lens while the illumination lamp
Y This product should be operated only with the type of poweris turned on. Exposure of your eyes to the stronglight can
source indicated on the label. If you are not sure of the typeresult in impaired eyesight.
of power supply to your home, consult your product dealer or
Y Do not look into the inside of this unit through vents (ventila-
local power company.
tion holes), etc. Do not look at the illumination lamp directly
Y This product is equipped with a three-wire plug. This plugby opening the cabinet while the illumination lamp is turned
will fit only into a grounded power outlet. If you are unable toon. The illumination lamp also contains ultraviolet rays and
insert the plug into the outlet, contact your electrician to in-the light is so powerful that your eyesight can be impaired.
stall the proper outlet. Do not defeat the safety purpose of
Y Do not drop, hit, or damage the light-source lamp (lamp unit)
the grounded plug.
in any way. It may cause the light-source lamp to break and
YPower-supply cords should be routed so that they are notlead to injuries. Do not use a damaged light source lamp. If
likely to be walked on or pinched by items placed upon orthe light-source lamp is broken, ask your dealer to repair it.
against them. Pay particular attention to cords at doors, plugs,Fragments from a broken light-source lamp may cause inju-
receptacles, and the point where they exit from the product.ries.
YFor added protection of this product during a lightning storm,Y The light-source lamp used in this projector is a high pres-
or when it is left unattended and unused for long periods ofsure mercury lamp. Be careful when disposing of the light-
time, unplug it from the wall outlet and disconnect the cablesource lamp. If anything is unclear, please consult your dealer.
system. This will prevent damage to the product due to light-
Y Do not Oceiling-mount� the projector to a place which tends
ning and power line surges.
to vibrate; otherwise, the attaching fixture of the projector
Y Do not overload wall outlets, extension cords, or conveniencecould be broken by the vibration, possibly causing it to fall or
receptacles on other equipment as this can result in a risk ofoverturn, which could lead to personal injury.
fire or electric shock.
Y Use only the accessory cord designed for this product to pre-
YNever push objects of any kind into this product through open-vent shock.
ings as they may touch dangerous voltage points or shortThe power supply voltage rating of this product is AC 120 V,
out parts that could result in a fire or electric shock.AC 100 V� AC 240 V, the power cord attached conforms to
Never spill liquid of any kind on the product.the following power supply voltage. Use only the power cord
designated by our dealer to ensure Safety and EMC.
Y Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltages andWhen it is used by other power supply voltage, power cable
other hazards. Refer all service to qualified service personnel.must be changed.
Ensure that the power cable used for the projector is the cor-
Y Unplug this product from the wall outlet and refer service to
rect type for the AC outlet in your country.
qualified service personnel under the following conditions:
Consult your product dealer.
a) When the power supply cord or plug is damaged.
Power cord
b) If liquid has been spilled, or objects have fallen on the prod-
uct.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the Operation Manual, as an improper adjust-For United KingdomFor European
continent countries
ment of controls may result in damage and will often re-
quire extensive work by a qualified technician to restore
Power cord
the product to normal operation.
e) If the product has been dropped or damaged in any way.
f ) When the product exhibits a distinct change in perform-
ance - this indicates a need for service.
Power supply voltage: AC 120 V
Y When replacement parts are required, be sure the service
technician has used replacement parts specified by the manu-
*DO NOT allow any unqualified person to install the unit.
facturer or with same characteristics as the original part. Un-
Be sure to ask your dealer to install the unit (eg.
authorized substitutions may result in fire, electric shock, or
attaching it to the ceiling) since special technical knowl-
other hazards.
edge and skills are required for installation.
Y Upon completion of any service or repairs to this product,
If installation is performed by an unqualified person, it may
ask the service technician to perform safety checks to deter-
cause personal injury or electrical shock.
mine that the product is in proper operating condition.
3 |
ACEC
