Filename [DX5SUS_13Subsidiary.fm]
DX5SUS_00.book Page 77 Thursday, September 1, 2005 2:35 PMMasterpage:Right0
TROUBLESHOOTING
EN 77
Before requesting service for a problem, use this chart and see if
Playback (DVD Deck)
you can solve the trouble yourself. Small problems are often easily
solved, and this can save you the trouble of sending your unit off The DVD deck cannot be operated.
for repair.IThe DVD deck is not selected.
Initializing (DVD Deck Only)] Press DV/HDD/DVD SELECT on the unit repeatedly or DVD on
the remote control so that the DVD lamp lights up on the unit.
Malfunction occurs on the unit.
Images do not appear on the TV screen.
] Press A to turn off the unit, press and hold A, then press o
IThe TV receiver?s channel selector is not set to the AV mode.
for two seconds or more.] Set the TV to its AV mode.
IWhen interlace scanned program is played back, progressive
Generalscan mode is selected.
No power is supplied to the unit.] Press and hold PROGRESSIVE SCAN until q disappears
from the front display panel. (A pg. 76)
IThe AC power plug is disconnected from the AC outlet.
] Connect the AC power plug to the AC outlet securely. Playback does not start or stop immediately after playback is
(A pg. 18)started by pressing I.
On the front display panel, ANO DISCB appears.
The remote control does not work properly.
IThe disc is loaded upside down.
] Remove the batteries, wait for 5 minutes or more, then load the ] Place the disc on the disc tray with the playback surface facing
butteries again.down. (A pg. 10)
IThe setting of the remote control code is inappropriate.IA disc not being compatible with the unit is loaded.
] Set the same remote control code (1, 2, 3, or 4) on both the unit ] Load a playable disc on the unit. (A pg. 7)
and the remote control. (A pg. 67)IA dirty disc is loaded.
IThe batteries are discharged.] Clean the disc. (A pg. 11)
] Replace the dead batteries with new ones.IDefective disc is loaded.
] Replace the warped or scratched disc with a normal one.
Dubbing from the external equipment is not possible.
Images are blurred or distorted when you start High-Speed
IThe source (another video recorder, camcorder) has not been Search.
properly connected.
] Confirm that the source is properly connected.] Images are blurred or distorted at the point where the playback
IAll necessary power switches have not been turned on.speed changes and this is not a malfunction of the unit.
] Confirm that all units? power switches are turned on.
IThe setting of the input channel position is inappropriate.Playback does not start.
] Select the input channel position (AF-1B or AL-1B) that
] Playback does not start for approximately 30 seconds after
corresponds to the input terminal connected to the external recording is stopped and this is not a malfunction of the unit.
equipment. (A pg. 63)
Playback does not start when you select a title or a chapter.
The on-screen display superimposed on the program played
back/received on this unit is recorded when you dub the IThe Parental Lock is engaged and the disc is rated higher than
program to an external recording equipment.the set level.
] Release the Parental Lock temporarily or change the set level.
] Set ASUPERIMPOSEB to AOFFB. (A pg. 72)(A pg. 33)
The unit does not operate.
Playback (HDD Deck)
IThere are cases when the operation is prohibited on the disc.
ILightning or static electricity may cause malfunction of the unit.The HDD deck cannot be operated.
] Press A to turn the power off, then press the button again to
IThe HDD deck is not selected.
turn the power on.] Press DV/HDD/DVD SELECT on the unit repeatedly or HDD on
The remote control of a JVC TV will not operate the unit.the remote so that the HDD lamp lights up on the unit.
IThe setting of the remote control code is inappropriate.
] To operate the unit using a JVC TV remote control, set the
remote control code of the unit to A1B (Default: A3B). (A pg. 67)
Page 77Thursday, 1 September 2005 14:35 |
ACEC
