Filename [MX1S_05Name.fm]
MX1S_00.book Page 20 Saturday, October 30, 2004 4:18 PMMasterpage:Left0
INITIAL SETTINGS
20 EN
1Connect the antenna cable to the unit. (pg.19) Then connect
Plug & Play Setthe AC power cord to an AC outlet. Do not turn on the unit.
The clock and tuner channels will be set automatically.
I ?LOADING? blinks on the front display panel when the AC plug of the
Auto Clock Set/Auto Tuner Set
AC power cord is connected into an AC outlet and it takes
This unit sets the clock and tuner channels automatically when AC approximately 50 seconds for the unit to be turned on. This is not a
power cord is first connected to an AC outlet. The antenna cable malfunction.
must be connected for the Plug & Play setting. NOTES:
The time and date can be set automatically by the clock setting I Auto Clock Set is performed first.
data transmitted from one of the regular TV broadcast channels. ?AUTO? blinks on the front display panel during Auto Clock Set.
We call this TV channel the ?host channel? and it is a PBS channel I Auto Channel Set is performed next. Auto Channel Set scans all the
in your area.channels that are receivable by your unit. During Auto Channel Set,
the channel numbers are displayed as they are scanned and set.
ATTENTION:I When Plug & Play setting has been completed successfully, the
I If you use a cable box, Plug&Play will not function; set the clock correct clock time is displayed. If you perform Plug & Play setting
and tuner channels separately. ( pg. 22 - 23)successfully, there is no need to perform ?Clock Set? ( pg. 22) and
I Depending on areas or reception conditions, the unit may not ?Tuner Set? ( pg. 23). If, however, you want to add or delete
receive the Auto clock setting data from the PBS channel. If this channels, refer to ?Manual Channel Set? ( pg. 23).
function is taking a considerable amount of time, it may be
During Auto Clock Set
necessary to perform the Semiauto or Manual Clock Set
?AUTO? blinks.
procedure.
STANDBY/ ONVHS/HDD/DVD
SELECT
HDD/DS-VIDEOVDVIDEO (MONO)L-AUDIO-RCHVRS -HDD -DVD -DISPLAY VHS TIMERREC MODEDV IN
F-1
During Auto Channel Set
The channel numbers are displayed and ?AUTO? blinks as they
are scanned and set.
INFORMATION
I If ?AUTO CLOCK? is set to ?ON? ( pg. 22), the clock will be
adjusted automatically by the host channel every hour (except
Plug&Play Completed
11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming
The current time is displayed.
PBS channel clock setting data. (This automatic clock adjustment
I If an incorrect clock time or ?- -:- -? appears on the front display
can only be performed when the unit is turned off. The clock will be
panel, see ?What to do if Plug & Play setting failed? ( pg. 20).
adjusted just on these hours ? on the time displayed on the front
display panel, not on the actual real time.) The default setting of
?AUTO CLOCK? is ?ON?. ( pg. 22)
I If the memory backup fails, because a power outage occurs or
because the AC power cord is unplugged, Plug & Play will be
performed when power is restored to the unit.
What to do if Plug & Play setting failed
I If an incorrect time is displayed on the front display panel, you may
be receiving the clock setting data of a PBS channel from an
adjacent time zone, or an incorrect PBS channel from a cable TV
system. In this case, perform ?Semiauto Clock Set? ( pg. 22) or
?Manual Clock Set? ( pg. 22).
I If ?- -:- -? appears on the front display panel, your antenna cable
may not be connected to the unit or there may not be a Host PBS
signal available in your area. Ensure that the antenna cable is
connected correctly. Then turn on and off the unit; the Plug & Play
setting will be automatically reactivated. If Plug & Play setting is
not performed though the antenna cable is connected correctly,
perform ?Manual Clock Set? ( pg. 22) and ?Auto Channel Set?
( pg. 23) or ?Manual Channel Set? ( pg. 23).
Page 20Saturday, 30 October 2004 16:18 |
ACEC
