Preparations
Checking the Accessories
Note:The following accessories are included with the Monitor. Check for them. If any item is missing, please contact the dealer where
* GM-P420PCE and GM-P421PCE do not haveyou purchased the Monitor.
the following input terminalsVIDEO A,
VIDEO B, and COMPONENT/RGB B. To" Remote control (RM-C576) x 1
input video, S-video, and component" Power cord x 2 (Use the one matching the wall outlet.)
signals, you need to install video input unitENGLISH" Batteries (AA/R6P) x 2
(IF-C422P1G), which is separately
purchased.
Installing the Batteries
Put the batteries in the remote control as follows. If the remote control has become erratic in operation, change the batteries.
1Remove the back cover.
While pushing the release lever on the cover, remove the cover in
the direction of the arrow.
89p
No.51953
2Place the batteries.
Put the two supplied batteries (AA/R6P), noting the a and ?
markings, as shown.
VIDEOAUDIOVIDEOAUDIOVIDEOAUDIO
L/MONOL/MONOL/MONO
INOUTRINY/C INRY/G Pb/BPr/RHD/Cs VD R
VIDEO AVIDEO BCOMPONENT/RGB B
3Replace the back cover as illustrated.
Make sure the release lever on the cover is locked in place correctly.
8 VIDEO A terminals (page 12)*p COMPONENT/RGB B input terminals (page 12)*
"VIDEO IN terminal (BNC)" R, G, B, HD/Cs, VD (VIDEO) input terminals (BNC)
Connect this terminal to the video output terminal of aConnect these terminals to the following output
VCR, etc.terminals of a personal computer or other equipment:
Analog RGB signal output terminalsPrecautions for using batteries"VIDEO OUT terminal (BNC)
Horizontal sync (HD) signal or composite (Cs) signalIf batteries are used improperly, the liquid could leak out, causing a fire, injury, etc. or dirtying the vicinity.Connect this terminal to the video input terminal of
output terminalTake notice of the following:another Monitor.
Vertical sync (VD) signal output terminal" Do not mix old and new batteries.
"AUDIO (L/MONO, R) input terminals (pin jack)" Do not mix different types of battery as different types may have different characteristics.
Connect these terminals to the audio input terminals of aNotes:" Place the batteries according to the a and ? markings indicated on the battery compartment.
VCR, etc."External sync signals are automatically detected when" When installing the batteries, insert the ? end first to avoid a short circuit.
they come in.
Note:" Use only the specified batteries.
"When both horizontal (HD)/vertical (VD) sync and
"Since the video output terminals on this Monitor are" When you are not using the remote control for a long time, remove the batteries.
loop-though terminals, the devices connected to thiscomposite (Cs) sync are connected, HD/VD sync signals" When the batteries have reached the end of their life, replace them with new ones immediately. Otherwise, the liquid may leak
will be used.
video output terminal should be correctly terminated.out, or malfunction may be caused by the leaked liquid. If the leaked liquid contacts your skin, wipe off the liquid with a soft
Otherwise, pictures become abnormally bright or thecloth. If the affected skin is left as is, you may get a rough skin.
Monitor screen gets affected abnormally." Y, Pb, Pr (VIDEO) input terminals (BNC)" Do not throw the batteries into fire or try recharging them.
Connect these terminals to the component signal output" The service life of batteries is six months to one year for normal use. The supplied batteries are only for checking the operation
9 VIDEO B terminals (page 12)*terminals of NTSC or high-vision equipment.and their life may be shorter. When the remote control operation becomes erratic, replace with new batteries.
"Y/C (S video) IN terminal (mini DIN 4pin)Note:
Connect this terminal to the S-video output terminal of a"When these terminals are used as the componentThe instruction below applies only to
VCR, etc.terminals (Y, Pb, Pr)see Setting the COMPONENT/the use in Holland.
RGB B Input on page 23, external sync signals (HD/Cs,Gebruike batterijen:"VIDEO IN terminal (pin jack)
Connect this terminal to the video output terminal of aVD) cannot be used.
VCR, etc.
"AUDIO (L/MONO, R) input terminals (pin jack)"AUDIO (L/MONO, R) input terminals (pin jack)GM-P421PCE GM-P420PCE
Connect these terminals to the audio output terminals ofConnect these terminals to the audio output terminals of
a VCR, etc.the other equipment.GM-P420E
Note:
"When both the video and S-video terminals are
connected, the S-video terminal will have priority.
1-578 |
ACEC
