To reset the Color-Reverse setting
2Press 5/ to move the cursor (3) to
After step 2 on the left column, proceed as follows:
OCOLOR-REVERSE� (on the second
1 Press 5/ to move the cursor (3) to Oreset.�
page), then press 3.
2 Press 3.
Y The Setup Menu consists of two pages. If you keep
The confirmation screen appears.
pressing 5/ , you can move to the other page from
reset
the current page.
Are you sure?
"YES" then key.
"NO" then key.MENU
SET-UP MENU 2/2
PIXEL SHIFT: OFF
POWER SAVE: OFF
COLOR-REVERSE3 Press 3 again to reset the setting.
REFRESH
reset
all resetTo cancel the reset, press MENU/EXIT (or MENU on the
HOUR METER x100h: 123
MODEL :GM-X50Ver. A
CATEGORY. UMonitor).
ADJUST:SELECT:EXIT:MENU
Notes:
Y The Color-Reverse function requires considerable time to
3Press 5/ to select the item you want
reduce the afterimage. Deactivate the function temporarily
to set and set the item as follows.at intervals of 30 minutes-1 hour and check the screen if the
afterimage still remains or not. Set the function to off if the
COLOR-REVERSEafterimage has been reduced.
You can activate/deactivate the function manually.
Press 2/3 to select the desired setting.
Refreshing the Screen
ON:The function is activated immediately after
exiting the menu operations.
After the power is turned off, a whitish image may be left on
OFF:The function is deactivated.the screen. In that case, leave the monitor in a white back state
TIMER: Select this when you use the Color-Reversefor a while, and the image will disappear.
On/Off Timer.You can activate/deactivate the function with the Refresh
Note:On/Off Timer.
Y Set the clock (see page 26) and select OTIMER,� before
using the Color-Reverse On/Off Timer.1On the remote control:
Press VOLUME � while holding MENU/
START SET
EXIT to display the Setup Menu.
You can activate/deactivate the Color-Reverse On Timer.
Press 2/3 to select OON� or OOFF.�On the Monitor:
ON: The function is automatically activated at the
Press 2 while holding MENU to display
time set in OSTART TIME.�
the Setup Menu.
OFF: The Color-Reverse On Timer is deactivated.
SET-UP MENU 1/2
START TIMECursor (3)STATUS DISPLAY: OFF
CONTROL LOCK: OFF
You can adjust the time to activate the function.REMOTE SWITCH: MODE1
HD SIGNAL MODE: 1080i
FAN SPEED: LOW
Y Set the hour and minute following steps 4 to 6 inWHITE BALANCE
TIMER
OSetting the Clock� (page 26).
ADJUST:SELECT:EXIT:MENU
END SET
You can activate/deactivate the Color-Reverse Off Timer.
2Press 5/ to move the cursor (3) to
Y Press 2/3 to select OON� or OOFF.�
ON: The function is automatically deactivated at theOREFRESH� (on the second page) then
time set in OEND TIME.�
press 3.
OFF: The Color-Reverse Off Timer is deactivated.Y The Setup Menu consists of two pages. If you keep
pressing 5/ , you can move to the other page from
END TIMEthe current page.
You can adjust the time to deactivate the function.
Y Set the hour and minute following steps 4 to 6 inSET-UP MENU 2/2
PIXEL SHIFT: OFF
OSetting the Clock� (page 26).POWER SAVE: OFF
COLOR-REVERSE
REFRESH
reset
all reset
4Press MENU/EXIT (or MENU on theHOUR METER x100h: 123
MODEL :GM-X50Ver. A
CATEGORY. U
Monitor) repeatedly to exit from the
ADJUST:SELECT:EXIT:MENU
menu operations.
(To be continued on the next page)
29
22-31_GM_X50[US].p652904.1.27, 8:38 AM |
ACEC
