33
AnimationTime-Lapse
Give stationary scenes or objects an illusion ofYou can record sequentially at preset time spans.
movement. This function allows you to shoot aLeaving the camcorder aimed at a specific subject,
series of pictures, each slightly different, of the sameyou can record subtle changes over an extended
object for a brief period of time.period of time.
ENGAGE RECORD�STANDBYENGAGE RECORD�STANDBY
MODEMODE
Make sure the lens cover is open, then set theMake sure the lens cover is open, then set the
1power switch to OCAMERA�.1power switch to OCAMERA�.
SET RECORDING TIMESET RECORDING TIME
Press REC TIME on the remote control. FourPress REC TIME on the remote control. There
2choices are available, and they appear in the2are four choices available, and they appear in
following order (each time REC TIME isthe following order (each time REC TIME is
pressed): 1/4S (one-fourth of a second), 1/2Spressed): 1/4S, 1/2S, 1S, and 5S. Press again to
(one-half of a second), 1S (one full second) andreset.
5S (five seconds). Press again to release theYYou can also set the recording time in the
Animation mode.
Sub Menu screen. Press O�� to move the
highlight bar down to ORec Time�, and press
YYou can also set the recording time in the
NEAR, then press + or � to cycle through the
Sub Menu screen (Z pg. 32). Press O�� tochoices.
move the highlight bar down to ORec Time�,
press NEAR, and press + or � to cycle
through the choices. Then press MENU.SET INTERVAL BETWEEN
RECORDINGS
START RECORDINGPress INT. TIME on the remote control. There
Press the Recording Start/Stop button after3are five choices available, and they appear in
3focusing on the subject. The recording stopsthe following order (each time INT. TIME is
automatically after the selected period of time.pressed): OFF, 15S, 30S, 1 min, and 5 min.
Press again to reset.
ASSEMBLE SERIES OFYYou can also set the interval time in the Sub
PICTURESMenu screen. Press O�� to move the highlight
bar down to OInterval Timer�, press NEAR,
Repeat steps 2 and 3 for the desired number of
4pictures.and press + or � to cycle through the choices.
YExposure control (Z pg. 20), manual
CHECK YOUR WORKfocusing (Z pg. 23) and D.I.S. settings
(Z pg. 20) should be performed at this point.
Play back the series of pictures to see if theOnce you perform step 5, these settings
5results were satisfactory.cannot be changed.
RELEASE ANIMATION MODESTART TIME-LAPSE
Press REC TIME until O� disappears from the
6viewfinder, or set ORec Time� in the Sub MenuRECORDING
Press the Recording Start/Stop button. Record-
screen to OOFF�.
4ing and intervals alternate automatically.
NOTES:
RELEASE TIME-LAPSE MODE
cFor best results, make sure the camcorder is
secured when shooting in Animation orTo release when the tally lamp is not blinking,
5press INT. TIME and REC TIME repeatedly
Time-Lapse mode.
cFade-in/out cannot be performed duringuntil O � and O � disappear. To release
when the tally lamp is blinking, press the
Animation or Time-Lapse shooting.
cBefore performing other operations followingRecording Start/Stop button to stop the
blinking, then press INT. TIME and REC TIME
Animation or Time-Lapse recording, make sure
repeatedly until O� and O � disappear, or
the Animation or Time-Lapse mode is deactivated.set OInterval Timer� and ORec Time� in the Sub
Menu screen to OOFF�.
GR-AX760EA3396.10.22, 3:56 PM |
ACEC
