Make sure OREMOTE� in the SYSTEM Menu is setPlayback Special Effects
to OON� ( pg. 23) and the remote control is
To allow you to add creative effects to the playback
pointed at the remote sensor !. The transmitted
image.
beamOs approximate effective distance for indoor
use is 5m.1To start playback, press PLAY (4) j.
2Point the remote control at the camcorderOs remote
sensor and press EFFECT I. The PLAYBACK
Slow-Motion Playback
EFFECT Select Menu appears.
To allow slow-speed search in either direction during3Move the highlight bar to the desired effect by
tape playback.pressing EFFECT I. The selected function is activated
1To change from normal to Slow-Motion Playback,and after 2 seconds the menu disappears.
press SLOW (9) R or (0) E more than approx. 2 To deactivate the selected effect, press EFFECT ON/
seconds. After approx. 5 minutes (approx. 20 secondsOFF U on the remote control. Pressing it again re-
with an 80-minute cassette) in Slow Rewind or approx.activates the selected effect.
5 minutes in Slow Forward, normal playback resumes. To change the selected effect, repeat from step 2
To stop Slow-Motion Playback, press PLAY (4) j.above.
NOTES:NOTE:
I You can also engage Slow-Motion Playback from StillThe effects that can be used during playback are Classic
Playback by pressing SLOW R E more than approx.Film, Monotone, Sepia and Strobe. The effects work the
2 seconds.same in playback as they did in recording. Refer to page 16
I During Slow-Motion Playback, due to digital imagefor more information.
processing, the picture may take on a mosaic effect.
I After SLOW (9) R or (0) E is pressed and held, the still
image may be displayed for a few seconds, followed by aPlayback Zoom
blue screen for a few seconds. This is not a malfunction.
To magnify the recorded image up to 44X at any time
I There may be a small margin between the slow-motion
playback start point you chose and the actual start pointduring playback.
for Slow-Motion Playback.1Press PLAY (4) j to find the scene of interest.
I During Slow-Motion Playback, there will be disturbances
in video and the picture may seem unstable, especially2Press the Zoom Button T p or W o on the remote
with steady images. This is not a malfunction.control. Make sure the remote control is pointed at the
I During Slow-Motion Playback, press PAUSE (6) ; tocamcorder's remote sensor. Pressing T p zooms in.
pause playback.
3You can move the image on screen around to find a
particular portion of the picture. While holding down
iaSHIFT W, press (Left) R, (Right) E, (Up)
g and (Down) h.
o
ps To end zoom, press and hold W o until magnification
Qdreturns to normal. Or, press STOP (5) l and then
Wfpress PLAY (4) j.
Eg
Rh
TjNOTES:
Yk
UlI Zoom can also be used during slow-motion and still
playback.
I;
OAI Due to ditital image processing, the quality of the image
PSmay suffer.
Normal playbackPress T p
Frame-By-Frame Playback
To allow frame-by-frame search during tape playback.
1To change from normal to Frame-By-Frame
Playback, press SLOW (0) E repeatedly for forward or
SLOW (9) R repeatedly for reverse. Each time it isTo move image, press
pressed, the frame is played back.(Right) E while keeping
SHIFT W held down.
NOTE:
You can also engage Frame-By-Frame Playback from Still
Playback by pressing SLOW (9) R or (0) E repeatedly.
EN
USING THE REMOTE CONTROL UNIT
28 |
ACEC
