47
mode, the audio level volume cannotaudio level controls on the CH-1 and
toring speaker.
ted to the INPUT1/2 connector, set the AUDIOcrease the audio monitoring volume exces-
LL AUTO is output mixed.me of the alarm tone is set with the ALARM VR
peaker or earphone outputs an alarm tone in theonnecting a stereotype earphone, make the fol-
SELECT switch.MONITOR volume control adjusts the monitoring vol-uds
hen the AUDIO INPUT switch is set to MIC, be sure to sively; otherwise howling with the camera microphone may occur.wing settings to output stereo sound.Set the MONITOR SELECT switch to BOTH.Set the AUDIO MONITOR item on the AUDIO/MIC menu screen to STEREO.hen AUDIO MONITOR item on the AUDIO/MIC menuEVEL item on the OTHERS [1/2] menu screen. (OFF/
check that the microphone is connected to the INPUT1/2 connector. If the microphone is not connected, increasing the audio level could cause noise from the input connec- tor to be recorded on the tape. When the microphone is not connecINPUT switch to ?LINE? or turn down the audio level con- trol.be adjusted with the CH-2.elect the audio channel to be monitored using the MONI-helo12screen is set to ?STEREO?, only the audio of CH-1 is out- put from the moniLLOW/MIDDLE/HIGH)
CAUTION?W?In the FUMEMOThe reference level for audio recorded on the tape can be set with the AUDIO REF. LEVEL item on the AUDIO/MIC menu screen. (-20 dB or -12 dB) The level will change for both CH-1 and CH-2.Monitoring Audio during RecordingTOR CH-1:The sound input to the CH-1 channel is output. BOTH:The sound input to the CH-1 and CH-2 channelsCH-2:The sound input to the CH-2 channel is output.ume.case of an abnormal condition occurring in the unit. An alarm tone is also output when the tape end is reached or when the battery is running down. *Do not inMEMO?When c?W?The volu
?The audio input during recording, in record-pause or stop mode can be monitored through the monitoring speaker or earphone. ?S?T?The lo
SETTING AND ADJUSTMENTS BEFORE SHOOTING
PHONES jack
into CH-2.into CH-2.
equipment, etc. The reference input level is +4 dBs.phone.tom microphone) requiring +48 V DC power sup- ply is connected.
select the normal input level for MIC and MIC+48Vust so that the peak level does not exceed the -3 dB
point when a loud sound is input.
rded in CH-2. Set the CH-1/CH-2 AUDIO SELECT switch of the channel whose audio level that you want to adjust manually to MANUAL.Rotate the audio input level control corresponding to the audio input level to be adjusted. ?Adj
Selecting the CH-2 channel input con- nectorSelecting the audio signal inputAdjusting Audio during RecordingAdjusting the audio input level control
MEMOThe audio from the INPUT1 connector is also input into CH- 1 regardless of the setting. CAUTIONWhen connecting a component that does not require +48 V power supply, make sure that the switch is not set to MIC+48V before the component is connected.MEMOYou can in the INPUT1, 2 MIC REF. item on the AUDIO/MIC menu screen.
The GY-HD100 is provided with the INPUT1 connector and the INPUT2 connector for audio input. Select the audio from the INPUT1 connector or the INPUT2 connector using the CH-2 INPUT switch for the audio to be reco?Select using the CH-2 INPUT switch. INPUT1:Inputs the audio from the INPUT1 connectorINPUT2:Inputs the audio from the INPUT2 connector?Select the sound to be input to the INPUT1 or INPUT2 con- nector using the AUDIO INPUT switch. The setting is made for each of INPUT1 or INPUT2 connec- tor.LINE:Set to this position when connected to audioMIC:Set to this position when using a dynamic micro-MIC+48V:Set to this position when a microphone (phan-?For each audio channel, use the CH-1/CH-2 AUDIO SELECT switch to select whether the audio level adjustment should be set to AUTO mode or MANUAL mode.?The audio input level can be adjusted manually when the GY- HD100 is in the record, record-standby or stop mode.1.2.
Monitor speaker
CH-1/CH-2 AUDIO SELECT switch
udio level
A
US 1 screen
CH-2 INPUT switchAT
ST
FULL AUTO switchCH-2 audio input level volumeIndicator level (reference)
f
INPUT
AUDIO switchMONITOR SELECT switchMONITOR volume
CH-1 audio input level volume
SETTING AND ADJUSTMENTS BEFORE SHOOTINGAudio Input Signal Selection46 |
ACEC
