Rear Panel Features(panel shown is 2466 - 2266C Combo panel is reversed)
ENGLISH
1234 56789
ENGLISH
1. Footswitch5. Ext FX (Bypass/Loop)Note: The impedance of the comboOs (2266C) ownThe correct value of mains fuse located in the small
Connecting the supplied footswitch here enablesWhen �outO this switch completely bypasses thespeakers is 8 ohms. Make sure the comboOs outputdrawer at the bottom of the mains socket is
you to perform two functions; you can change thecircuitry involved in the effects loop. Push this switchselector is set to 8 ohms when no extension cabsspecified on the rear panel of the amplifier. The
Dynamic Range and toggle the Reverb on and off.in to enable the loop.are connected.drawer contains a space for a spare fuse. NEVER
The Dynamic Range switch functions exactly theattempt to bypass the fuse or fit one of the incorrect
same as the front panel counterpart (11).Note: If this switch is accidentally pushed in and8. HT Fusevalue!
there is nothing plugged in to the loop, the signalThe correct value of this H.T. fuse is specified on
Effects Loop Send & Return Jackswill still pass through from send to return by meansthe rear panel of the amplifier. NEVER attempt toNote: It is wise to carry spare HT and Mains fuses!
To increase the flexibility of your amplifier evenof an internal link on the switching jacks.This link isbypass the fuse or fit one of the incorrect value!
further, you may choose to add external effects in itsdisconnected when something is plugged into the
Series Effects Loop, which allows direct connectionreturn socket.The send socket has no effect on the9. Mains Input Socket with incorporated
of either floor pedals or rack processors, with thestatus of the internal link and could therefore beMains Fuse
4used as a line out to a tuner for example if noYour amp is provided with a detachable mains
level. external FX are connected.powerThe specific
mains input voltage rating that your amplifier has
2. Send6. Speaker Outputsbeen built for is indicated on the back panel. Before
Connect the (mono) input of an external effectsWARNING! Never use the amplifier without a loadconnecting for the first time, please ensure that your
processor here.speaker cabinet/samplifier is compatible with your electricity supply. If
you have any doubt, please get advice from a
3. ReturnThere are two parallel loudspeaker output jacksqualified technician. Your Marshall dealer will help
monofectssyou in this respect.
processor here.ALWAYS ensure you use good quality speaker
shielded
Tonal tip: Effects involving distortion or Wah Wahcables.
arenOt usually put in an effects loop because they
sound best when they're �beforeO the amp (i.e.Always use a non-screened Marshall approved
placed between the guitar and the ampOs input).speaker lead when connecting an extension cabinet
However, when it comes to your sound, itOs up toto these units.
you!
7. Output Selector
4. Ext FX (-10dBV / +4dBu)This switch should be set to match your speakerTechnical Specification
This switch offers two different loop levels to enablecabinetOs impedance. If more than one speaker
you to match the type of efscabinet is connected then you should set the switch2466 Head2266 Head2266C Combo
Series Effects Loop. The higher level (+4dBu: switchto match the total impedance of the combination.Power (RMS)100W50W50W
�inO) suits rack processors and the lower levelCheck with your dealer if you are unsure.Valves4x ECC83 + 4x KT664x ECC83 + 2x KT664x ECC83 + 2x KT66
(-10dBV: switch �outO) suits floor pedals (stompFX Send Level - selectable-10dBV, +4dBu-10dBV, +4dBu-10dBV, +4dBu
boxes). 16 & 8 ohms are provided for on the heads (2466Weight 22.5kg18kg30kg
and 2266).Size (mm) W, H, D750 x 310 x 230750 x 310 x 230690 x 570 x 270
Note: A similar level matching switch may also be
found on rack effect units, in which case the amp2266C
and effects unit should be set to the same level.
Follow all instructions and heed all warnings
KEEP THESE INSTRUCTIONS !
45 |
ACEC
