FRONT PANEL FEATURES
a quality authorized replacement from your
local Numark retailer.
17. Crossfader Direction: Activation of this
switch reverses the assignment of CH-1 and
CH-2 on the crossfader.
18. Crossfader Contour Control: The position
of this control determines how quickly or
intensely the crossfader will blend.
19. Master Output Knob: This rotary control
adjusts the main output volume.
20. Stereo Level Indicator: quickly and
accurately tracks level of audio.
REAR PANEL FEATURES
Note: It is recommended that the mixer be
turned off before connecting and
1. Power LED: Illuminates when the mixer is disconnecting any sources to the inputs of the
on. mixer.
2. Mic Gain: This knob adjusts the volume of
the microphone input. 1. Microphone Input: Microphones with a 1?
3. Mic Treble: This knob adjusts the high-tone connector can be connected to this input
of the microphone. terminal.
4. Mic Bass: This knob adjusts the low-tone of 2. Phono Inputs: This input is used for
the microphone. connecting your turntables through the sensitive
5. Channel Gain: This rotary control adjusts RIAA phono preamplifiers. Only turntables with
the pre-fader input level. phono level output should be attached. Line
6. Channel Treble: This rotary control adjusts level turntables and other devices may be
the high-tone level. attached if the Phono/Line rear panel switch is
7. Channel Middle: This rotary control adjusts set to the line position.
the middle-tone level. 3. Phono/Line Source Switch: This switch
8. Channel Bass: This rotary control adjusts activates and deactivates the sensitive RIAA
the low-tone level. phono preamplifiers. Only turntables with
9. Input Selector: This toggles select what phono level output should be assigned
input source is routed to the channel from when the switch is in the phono position.
the rear panel connected units. Some turntables offer line level output. To use
10. Channel Fader: This slide fader is used to these turntables and other line devices like CD
adjust the level sent to program mix. players, switch the input to Line.
11. Headphone Volume: This rotary control 4. GND: This screw connector should be used to
adjusts the volume level of the headphone secure any turntables or other devices
output. connected to the mixer that need to be
12. Headphone Jack: Your headphones can be grounded.
connected to this 1? terminal. The volume 5. Line Inputs: CD players, Tape Decks, Samplers
should always be set at its lowest setting or other line level input devices should be
while connecting and disconnecting connected to these inputs.
headphones to prevent damage to 6. Record Output: This RCA output is for
headphones and/or your hearing. connecting a recording device such as a tape
13. Cue Slider: Channels 1 and 2 can be deck or CD recorder. The level of the record
previewed using this mini-crossfader. output is based upon pre-master levels.
Sliding this to the left plays the left 7. Master Output (RCA): This output is for
?channel-1? and sliding to the right plays the connecting an external monitoring device such
right ?channel-2?. as a PA system, powered monitors or a home
14. Cue Meter: This meter shows the peak, stereo. The level of the master stereo output
?PFL?, Pre Fader levels of channels 1 and 2. signal is controlled by the master fader.
You can use the channel ?Gain? and ?EQ? 8. AC In: This mixer is designed to work with the
controls to match the levels of input signals power supply assembly that comes with the
while cueing. unit. While the power is switched off, plug the
15. Master Cue Selector: When selected only power supply into the mixer first, then plug it
the master output is heard in the into the outlet.
headphones. 9. Power Switch: Use this switch to turn on the
16. Replaceable Crossfader: This slide fader mixer after all input devices are already
blends audio between the channels assigned connected to prevent damage to your
to the left and right assign switches. equipment. Turn the mixer on before you turn
Note: This fader is user replaceable if it on amplifiers and turn of amplifiers before you
should ever wear out. Simply remove the turn off the mixer.
facepanel and then remove the screws
holding it in position. Replace the fader with |
ACEC
