Troubleshooting
SymptomPossible causeRemedy
Connect the power cord to a suitable wall outlet
The power cord is not connected.
(page 37).
CanOt turn on the Turn off the DPS-10.5, wait Ţve seconds, then try
DPS-10.5?External interference is affecting the turning it on again. If that fails, disconnect the
DPS-10.5Os digital circuitry.power cord from the wall outlet, wait Ţve seconds,
reconnect it, then try turning it on again.
The DPS-10.5 turns itself The Auto power off function will turn the
The Auto power off function can be turned on or off
off when itOs not being DPS-10.5 off automatically after 20 minutes of
as required (page 80).
used?inactivity.
On your TV, select the input to which the DPS-10.5
The wrong input source is selected on your TV.
is connected (pages 27, 28).
Check the video cable and correct as necessary
No picture?The video cable is not connected properly.
(pages 27, 28).
Not all of the video outputs work with all disc See page 24 for details on how the DPS-10.5 out-
types and formats.puts video from each output.
The wrong input source is selected on your On your hi-Å¢ amp or AV receiver, select the input to
hi-Å¢ amp or AV receiver.which the DPS-10.5 is connected (pages 32, 34).
Check the audio cable and correct as necessary
The audio cable is not connected properly.
(pages 32, 34).
No sound?Your hi-Å¢ amp or AV receiver is turned off.Turn on your hi-Å¢ amp or AV receiver.
Check the Digital Out/Digital1 or Digital2 setting
The Digital Out settings are incorrect.
and correct as necessary (pages 70, 71).
Not all of the analog and digital audio outputs See page 25 for details on how the DPS-10.5 out-
work with all disc types and formats.puts audio from each output.
The disc is dirty.Remove the disc and clean it (page 12).
The picture distorts occa-
YouOre using the Fast Forward or Fast Reverse A little picture distortion may occur when using
sionally?
function.these functions. This is normal.
The DPS-10.5 is connected to your TV via a
Picture instability or Connect the DPS-10.5 directly to your TV (pages
VCR or other video equipment whose copy
noise?27, 28).
protection system is affecting the picture.
No disc loaded.Load a disc (page 41).
The disc is incompatible.Load only compatible discs (page 10).
The disc is upside down.Load the disc the correct way up (page 41).
Place the disc in the center of the disc tray
CanOt start playback?The disc is not centered in the disc tray.
(page 41).
The disc is dirty.Remove the disc and clean it (page 12).
The disc supports parental lock and the Paren-
Turn off the Parental Lock function (page 79).
tal Lock function is on.
CanOt watch the
The Priority Contents setting is set to Set the Priority Contents setting to DVD-VIDEO
DVD-Video material on a
DVD-AUDIO.(page 80).
DVD-Audio disc?
CanOt play the multichan-
The SACD Audio Setup setting is not set to Set the SACD Audio Setup setting to Multi ch Area
nel area of a hybrid
Multi ch Area.(page 76).
SACD?
This is because the i.LINK Output Setting is
set to Off. If the DPS-10.5 is properly con-
Set the i.LINK Output Setting to On (page 71).
SACD audio is not output nected to an i.LINK component and an SACD
by the i.LINK sockets?is loaded, the IEEE 1394 indicator will �ash.
Check the i.LINK connections and correct as nec-
The i.LINK cables are not connected properly.
essary (page 31).
SACD audio is not output
This is because the i.LINK Output Setting is
by the analog audio out-Set the i.LINK Output Setting to Off (page 71).
set to On.
puts?
89 |
ACEC
