Connecting to Audio/Video equipment
: Signal flow
Digital audio output (coaxial)
R (red)
Analog audio output
DIGITALPRAUDIOVIDEO S VIDEOCOMPONENTL (white)
INPUTTENNARVIDEO
COAXFRONTMONITOROUTPUT
1OUTYVideo output
RL
SUB
2AMOUTZONE 2PB
SURRS Video output
3INDVDPR
SURR R
OPTBACK/ ZONE 2INPUT 1FM
175OUTY
VIDEO 1
FRONT
2INPB4. DVD player (DVD)
RUDIOL
SUB
3PHONOOUTPR
VIDEO 2
SURRINPUT 2
4CDINY
ROUT
OPT
1INVIDEO 3PB
SURR
BACKTAPE
2INVIDEO 4PR
GNDLRLIN
DIGITALUDIOAUDIOVIDEO S VIDEOCOMPONENT
OUTPUTVIDEO
Y
PB
PR
Component video output
Connecting your video components4. Connecting a DVD player (DVD)
Using an RCA video cable, connect the video output jack
Below is an example of how you can connect your video components(composite) of the DVD or LD player to the DVD VIDEO IN jack of
to the DTC-9.4. Refer to the diagram above for the followingthe DTC-9.4. Or if the DVD or LD player has an S video output jack,
connection examples.connect it to the DVD S VIDEO IN jack with an S video cable. Or if
the device has component video outputs, connect them to one of the
COMPONENT VIDEO INPUT/OUTPUT
banks of COMPONENT VIDEO INPUT jacks on the DTC-9.4.
For DVD players or other devices that have component video
The default setting for DVD video input is set to OINPUT 1�
connectors, the DTC-9.4 has two banks of component video input
(COMPONENT VIDEO INPUT 1).
connectors (Y, PB, PR) for direct component video input. The DTC-
If you connect the DVD player to video jacks other than the
9.4 also has one bank of component video output connectors for
COMPONENT VIDEO INPUT 1 jacks, change the setting for
direct component video output to the matrix decoder of a television,
Ob.Component Video� at the O2-3.Video Setup sub-menu� to
projector, or other display device. By sending the pure component
appropriate value (see page 59).
video signal directly, the signal forgoes the extra processing that
normally would degrade the image. The result is vastly increasedUsing an RCA audio connection cable, connect the audio output
image quality, with incredibly lifelike colors and crisp detail.jacks of the DVD or LD player to the DVD AUDIO IN jacks of the
DTC-9.4. Make sure that you properly connect the left channel to the
VIDEO IN/OUT
L jack and the right channel to the R jack.
These are the video inputs and outputs. On the rear panel, there are
five video inputs and two video outputs and each one includes bothIf the device has a digital output, connect it to either the DIGITAL
composite video and S video configurations.INPUT COAX jack or DIGITAL INPUT OPT jack of the DTC-9.4
Connect VCRs, VTRs, LD players, DVD players, and other videodepending on the type of connector on the DVD player.
components to the video inputs. Connect VCRs, VTRs, and otherWith the initial settings of the DTC-9.4, the DVD input source is
recording components to the video outputs to make video
set for digital input at the COAX 1 jack.
recordings.
If the digital connection is made at a different jack, this must be
Y When connecting a VCR or other video component, make sure
changed at Setup Menu ? Input Setup ? Digital Setup (see page 57).
you connect its audio and video leads to the same bank (e.g.,
both to VIDEO 3).
Y The VIDEO 5 inputs are located on the front panel.
The flow of the video signals is as follows:
Signals that comes in from VIDEO and S VIDEO INPUT are output to
VIDEO, S VIDEO and COMPONENT VIDEO. However, signals
that comes in from COMPONENT VIDEO INPUT are only output to
COMPONENT VIDEO OUTPUT. When connecting a video player
to the COMPONENT VIDEO INPUT jacks, be sure to connect your
television to the COMPONENT VIDEO OUTPUT jacks.
18 |
ACEC
