Input Setup
2-1. Digital Setup sub-menu2-4. Listening Mode Preset sub-menu
b. Digital FormatWith the this unit, you can set a different listening mode
The default setting is OAll.� If O----� is selected for this input
for each different signal format that comes from each
source at the Digital Input setting, then this setting will notinput source and also set the parameters for the listening
appear. Although you can use this default setting as is,
mode itself. For example, if your DVD player also plays
you may change it as desired depending on the input
compact discs and the DVD video signal is DTS and the
signal format (e.g., if you know that you will always be
compact disc signal is PCM, then you can set a different
listening to a certain input signal format from a particular
listening mode for each.
input source).
This is especially convenient if you frequently play the
All: Detects input signal format automatically. The
same types of movies or music.
Dolby Digital, DTS, MPEG Multi, and PCM signals are
Note that some listening modes cannot be set for some
automatically detected and decoded appropriately.
input sources. In addition, if Omulti channel� is set for the
If there are no digital input signal, the input signal
input source selected, then the listening mode cannot be
coming into analog input jack will be played.
set. Also, if the O----� is set for the Digital Input setting in the
AC-3RF: Select this option when you play only AC-3RFDigital Setup sub-menu, then you can only select
signal which comes from AC-3RF output jack on a LDOAnalog/PCM.�
player to the AC-3RF input jack on you unit. When
using this option, signals from other input jack will not
Menu
be played. This option can be selected when you
select the VIDEO 4 for input source. 1.Speaker Setup123456789012345678901234
12.Input Setup
2.Input Setup
DTS: Select this option when you only decode DTS2 Input:FM
3.Listening Mode Setup
signal. Other format signals will not be played. 4.Preference3123456789012345678901234
41 1.Digital Setup2-4.ListeningMode Preset
5.Zone2 OSD Setup
PCM: Select this option when you only decode PCM52 2.Multichannel Setup Input:FM
6.About
signal. Other format signals will not be played.63 3.Video Setup a.Analog/PCM
74 4.Listening Mode Preset :Stereo
85 5.Sound Effect b.PCM fs>48k :Stereo
Select: Exit:|EXIT|
Note:96 6.Character Input c.PCM fs=192k :Stereo
Enter:|ENTER| Quit:|OSD|
07 7.Miscellaneous Setup d.Dolby D :Dolby D
If OAll� is selected and a compact disc or LD is fast-
18 e.DTS :DTS
forwarded during playback, decoded PCM signals may29 Quit:|OSD| f.MPEG Multi
produce a skipping sound. In such cases, change the0 :MPEG Multi
setting to OPCM.�2 g.D.F.2ch
:PLII/Neo:6
h.D.F.Mono:Mono
Notes on DTS:
Y If you play a CD or LD that supports DTS when the OPCM�
setting is selected on the this unit, the DTS encoded signal
will not be decoded and noise will be output. This noise
could damage the amplifier and speakers. Therefore, be
sure to selected OAll� or ODTS� and use the digital input
jacks (OPTICAL or COAXIAL) to connect the DTS source.
5.1-channel digital surround format
Y If you play a CD or LD that supports DTS when the OAll�
setting is selected, you may hear a noise for a short whileThe 5.1-channel digital surround format has a variety of
until the DTS decoder recognizes the DTS-encoded signalversions including Dolby Digital, DTS, and MPEG
and starts operating. This is not a malfunction.Multichannel. The 5.1- channel digital surround format
enables you to individually record and play five full-range
Y If you press the Opause� or Oskip� button on the player
(20Hz-20kHz) channels (left and right front, center, two
while playing a DTS source, a short noise may be
surround channels) plus an LFE channel (Low Frequency
heard. This is not a malfunction. In such cases, try
Effect) for the low-range effect sound. It will create a
playing the source in the ODTS� selected.
realistic sound that could be heard in the theaters and
Y The DTS indicator on this unit lights while a DTS source is
concert halls.
played. When playback finishes and the DTS signal
transmission stops, this unit remains in DTS mode and the
DTS indicator remains lit. This prevents noise when you
operate the Opause� or Oskip� button on the player.
Therefore, if the source is immediately switched from
DTS to PCM, the PCM signal may not be played. In this
case, stop the playback of the source on the player for
about three seconds and then resume playback.
Y You may not be able to play some DTS source signals
from certain CD players and LD players even if you
connect the player to this unit digitally. This is because
the digital signal has been processed (such as the
output level, sampling frequency, or frequency
response) and this unit cannot recognize the signal as
DTS data. Therefore you may hear noise when you
play a DTS source while processing the signal.
Y The outputs for the VIDEO 1 OUT, VIDEO 2 OUT, TAPE 1
OUT, and TAPE 2 OUT output analog audio signals. Do
not record from CDs or LDs that support DTS using
these outputs. If you do, the DTS-encoded signal will
be recorded as noise.
Upgraded-6 |
ACEC
