50P IN/OUT
ASSIGN
Function menus
<50P IN/OUT ASSIGN>
Registering functions in the input pins/Active inputsResetting all the items and values
Registering functions in the output pins/Active outputs
Press F4(RESET) while holding down the Fbutton.
1.Selecting the 50-pin connector pinsAll the registered item names and registered values
Turn the ADJ dial to move the selection marker are now set to the factory settings. (These settingsand
select the pin of the 50-pin connector into cannot be restored.)which the
menu item is to be registered.
Special IN menu list
2.Entering the 50-pin connector pinsNo.
SUPERDescription of setting
Press the ADJ dial.
DISPLAY
The entered 50-pin connector pin display is highlighted.
Functions not featured on the setup menua
3.Selecting the menu itemB00For transferring to the STANDBY ON mode.
STBY ON
Turn the ADJ dial and select the menu item for the pin
of the 50-pin connector which was selected B01in step 1For transferring to the STANDBY OFF mode.
above.STBY OFF
B02For alternately transferring to the STANDBY ON
4.Entering the menu item
STBY ONOFFand OFF mode.
Press the ADJ dial.
B03For transferring to the EJECT mode.
The on-screen setting display now blinks.
EJECT
B04For prerolling the tape to the IN point when the
5.Selecting the setting
CUEIN point has been registered; for prerolling the
Turn the ADJ dial and select the setting for the
tape to the current point when the IN point has
menu item which was selected in step 3 above.not been registered.
6.Entering the settingB05For registering the edit IN point.
IN SET
Press the ADJ dial.
What is to be operated by the ADJ dial returns B06 to theFor transferring to the still picture (STILL) mode.
front panel. Whatever was selected in step STILL3 is
displayed as the registered item name and whatever wasB07The 9-pin connector functions.
selected in step 5 is displayed as the registered value.422 REM ON
B08The 9-pin connector does not function.
7.To select menu items and settings for other 50-pin
422 REM OFF
connector pins, repeat steps 1 to 6.
B09For returning TC SOURCE to the previous EXT
TC EXTmode.
8.Saving the data in the 50-pin registration file
(No switching occurs if the EXT mode is
To save what has been set in the 50-pin connector in
currently established.)
the 50-pin registration file, press F5(SET).
B10For switching TC SOURCE to INT and TCG
If F6(EXIT) is pressed without the above settings
TC INT AUTOMODE to AUTO.
have been saved, those settings will be canceled.
B11For switching TC SOURCE to EXT_L and TCG
TC EXT_LMODE to REGEN.
Clearing
REG
1.Turn the ADJ dial to move the selection marker and SRC PROTECT and STOP PROTECT settings switched simultaneouslyselect the
pin of the 50-pin connector whose menu item is to be cleared.B20For switching the tape protection mode operation to
PROTECThalf-loading in the event that the VTR has been left
2.Press F4(RESET). The registered item HALFnamestanding in the STOP mode or the STILL mode while
any of the search modes (JOG, VAR or SHTL) was
and registered value displays now go blank.
established.
3.To clear the menu items in other 50-pin connectorB21For switching the tape protection mode operation to
PROTECTtension release when the VTR has been left standing
pins, repeat steps 1 and 2.
T-RELin the STOP mode or the STILL mode while any of the
search modes (JOG, VAR or SHTL) was established.
4.To save what has been set in the 50-pin connector in
the 50-pin registration file, press F5(SET).
If F6(EXIT) is pressed without the above settings
have been saved, those settings will be canceled.
73 |
ACEC
