Setup menus (continued)
<OPERATION> (continued)
No./ItemDescription of settingNo./ItemDescription of setting
1*1
111*For selecting whether to automatically stop the 113For selecting whether to allow or inhibit
VTR when the counter value is at the ?0? recording on the cassette tape.
position during CTL mode FF and REW 0000OFF
MEMORY REC INH
operations.Recording on the cassette tape is enabled when
STOP
0000OFFthe cassette?s accidental erasure prevention
The VTR does not stop.mechanism has been set to the recording enable
0001ONposition.
The VTR is automatically stopped.0001ALL
<Notes>All recording on the cassette tape is inhibited.
z Either the stop or still picture (SHTL STILL or 0002PRE
SLOW STILL) mode, whichever has been set Overwriting is inhibited during normal recording.
using setup menu item No.307 (AFTER CUE-This is the setting to activate the accidental
UP), is established when the VTR is stopped.erasure prevention function. While CTL is
z If both the AUTO REW function and MEMORY detected, the recording is inhibited, and when
function have been selected at the same time, CTL cannot be detected, it is executed.
the AUTO REW operation takes priority.0003NORM
112For selecting what playback images are to be Normal recording is inhibited.
output in the STANDBY OFF (HALF LOADING) Use this setting when it is preferable to avoid
FRZ MODE mode and EJECT mode.using normal recording in all applications except
SEL0000DISfor editing.
The video output is muted.0004V/CTL
0001 STB OFFThe recording of the video and CTL signals is
Only when the STANDBY OFF mode is estab-inhibited.
lished is the image which was being played back Use this setting when it is preferable to avoid
at that moment frozen and output.editing in all applications except for audio editing.
0002 SOF&EJ<Note>
When either the STANDBY OFF mode or the When the PRE, NORM or V/CTL setting has been
EJECT mode is established, the image which selected, the REC INHIBIT lamp blinks (on for
was being played back at that moment is frozen approx. 0.5 sec. and then off for approx. 0.5 sec.).
and output.114For selecting whether the REC INHIBIT lamp is to
<Notes>blink or light when the cassette tape has been set
z The status when the picture is frozen is REC INH to the accidental erasure protection mode.
determined by the setup menu item No.604 LAMP0000LIGHT
(FREEZE SEL) setting.The lamp lights.
z In the EJECT mode, the frozen picture is output 0001 FLASH
only when 1 (BLACK) or 2 (GRAY) has been The lamp blinks.
selected as the setup menu item No.106 (EJECT <Note>
EE SEL) setting.When Setup Menu No. 113 (REC INH) is set to
z When the 720/24p over 60p source is used and [ALL], the REC INHIBIT LAMP always lights
the 23/24 mode is selected in System Menu item regardless of the setting.
No. 25 (SYSTEM FREQ), playback cannot be 115*1For selecting whether to enable or disable the
frozen in EJECT mode.operation of the EJECT button on the VTR?s
front panel.
EJECT SW
0000REC
Description of MEMORY STOP functionINH
Operation is disabled while the VTR is in the
recording mode.
The MEMORY STOP function does
0001OFF
not work if this margin is less than 0
Operation is enabled in all modes.
0 pointd 2 frames.
116For selecting whether the EJECT lamp is to
remain lighted or go off after the cassette tape
3REW button1FF buttonEJECT LAMPhas been ejected.
0000 MODE1
The EJECT lamp remains lighted.
4FF button2REW 0001 MODE2
buttonThe EJECT lamp goes off.
Accidental erasure protection function
!If the FF button is pressed, the normal FF operation is
This function is used to prevent parts already recorded on a tape
performed since there is no 0 point in the direction of this from being recorded over. Accidental erasure of pre-recorded
operation.tapes is prevented by positioning the CTL signal rec/play heads as
@If the REW button is pressed, the PREROLL lamp lights (as shown in the figure below so that whether a recording has been
does the SHTL lamp), the VTR prerolls the tape, and it made can be determined by the presence or absence of the CTL
automatically stops when the counter value is at the 0 position.signal. When the REC/PLAY button is pressed with a pre-
#If the REW button is pressed, the normal REW operation is recorded tape, the tape runs but the REC button lamp blinks, the
performed since there is no 0 point in the direction of this beeping alarm is sounded, and no signals are recorded.
operation.
$If the FF button is pressed, the PREROLL lamp lights (as does A/C heads
the SHTL lamp), the VTR prerolls the tape, and it (rec/play heads)
automatically stops when the counter value is at the 0 position.
PRE CTL
*1: When the 23/24 Hz mode, 25 Hz (HD, SD) mode, or 50 Hz
head
(HD, SD) mode is selected in System Menu No. 25 (SYSTEM
FREQ), this item is not displayed.
Rough sketch showing CTL head positions
88 |
ACEC
