"+)%9@1@& 7259
@&1.�?´
Chapter 3 Recording and playback (continued)
<Notes>
3-6 To take the previous cut again
eThe rec-review function cannot be used unless recording
(RETAKE function)
lasts for one or more seconds.
eIf the VIDEO OUT OUTPUT SEL switch on the side panel
The RETAKE function ensures continuity with the previousis at the VTR position during the rec-review operation, the
cut on the tape when shooting is resumed.
rec-review images are output not only to the viewfinder but
It is set by opening the <REC FUNCTION> screen from the
to the video output connector (VIDEO OUT connector) as
SYSTEM SETTING page and selecting ON as the setting for
well.
the RETAKE MODE item by performing menu operations.3
Use the menu operations to open the <OUTPUT SEL>
The RETAKE MODE item settings are described below.screen from the SYSTEM SETTING page and set the
ON: The retake operation is performed when the RETMONI OUT MODE item to VTR to output video signals of
button on the lens is pressed while the MODE CHECKRec-review from the MON OUT connector as well.
button is held down.Bear in mind that if back-up images are being recorded by
OFF: The RETAKE function does not operate.a backup VTR that has been connected, these rec-review
images will end up being recorded.
If, when the rec-pause mode is established upon completion
The jump function as a relevant function. For details, refer
of the recording or the stop mode is established afterwards,
to �3-3 Scene-to-scene continuity.�
the RET button on the lens is pressed while the MODE
eAfter executing the rec-view operation, the time code at the
CHECK button is held down, the tape will be rewound to the
time of recording the following data will correspond to the
approximate start point (a position advanced by 10 or so
settings in the REC REVIEW REGEN item (<TC/UB>
frames from the recording start) of the final image that was
screen on the VTR MENU page).
last recorded, and the rec-pause mode will be established.
eWhen the REC REVIEW REGEN item is turned ON and
If there is some leeway in the shooting time and a �NG�
the rec-view operation is executed while the TCG switch is
condition has been clearly identified, recording can be
set to the R-RUN position, the time code will always be
started from this point, and the cut in the NG area will be
regenerated to the value on the tape.
deleted.
Even if the TCG switch is set to the SET position or the F-
This function is particularly useful for cutting the amount of
RUN position, the time code will be rewritten to the value
time taken for copying onto work tapes and other such
on the tape when the rec-veiw operation is executed after
economical operations.
returning the switch to the R-RUN position. When recording
starts, the unit regenerates the time code to the value on
Direction of tape travel
the tape. Even if the FIRST REC TC item of the menu
(TC/UB screen of the VTR MENU page) is set to PRESET,
Cut 1Cut 2Cut 3
the time code will always be regenerated to the value on
Approx. 10 framesthe tape by executing the rec-view operation after setting
the TCG switch to the R-RUN position.
Cut 1Cut 2Cut 4
Direction of tape travel
Cut 3
Rec-pause
Recording sectionNo recorded or already recorded section
When the RETAKE function is to be exited
2 to 10 sec.
There are two ways to do this.Rec-review operation
Rec-pause
1) Set the unit�s POWER switch to OFF.
2) Perform a menu operation and select OFF as thePlayback of recorded section
RETAKE MODE item setting.
3-7 To check the last few seconds of
3-8 Normal playback and playback
the recording
at different speeds
(Rec-review function)
Black-and-white playback images can be viewed in the
When recording is temporarily stopped and the lens RET
viewfinder by pressing the PLAY button. When a color
button is pressed, the last two seconds of the tape are
monitor is connected to the unit�s VIDEO OUT connector and
automatically rewound, and the playback pictures on this part
an HD color video monitor is connected to its MON OUT
of the tape appear on the viewfinder screen. This makes it
connector at the same time, the down-converted color
possible to check whether recording was performed properly.
playback images from the VIDEO OUT connector can be
After the two seconds of the tape have been played back,
viewed on the color monitor while the HD high-quality images
the unit is again set to the recording start standby mode.
from the MON OUT connector can be viewed on the HD
If the RET button is held down, a maximum of 10 seconds of
color video monitor.
the tape is rewound and played back.
The Rec-review function can be executed by opening theeIn order to view these images, the OUTPUT SEL switch on
the side panel must be set to the VTR position.
<SW MODE> screen from the OPERATION page and
setting the RET SW items to the R. REVIEW via menuIn addition, when the FF and REW buttons are used, the
operations.images can be played back at different speeds by
The RET button function can be allocated by opening theestablishing the cue mode (PLAY + FF), review mode (PLAY
<USER SW> screen from the OPERATION page and+ REW), high-speed fast forward playback mode (FF) or
selecting settings for the USER MAIN SW, USER1 SW andhigh-speed rewind playback mode (REW).
USER2 SW items by performing menu operations.
29 |
ACEC
