5.MENU/DIAG buttonmove to the previous recording slot position.Pressing
this button when the unit is in slot 1 results in a move to
MENU button
slot 6.
Press this button to open the MENU. Press again to
return to the previous screen.
DIAG (SHIFT+MENU) button
8.ENTRY/CLIP (LIST/PF2 button)
Press to show information about this unit. Press again
Use these functions to create play lists.
to return to the previous screen. However, this function
Pressing the IN, OUT or SPLIT button simultaneous
is not available while thumbnails or play lists are Introduction
with this button while registering an event (the PLAY
displayed.
LIST and EVENT buttons are on), allows you to set the
Information about this unit include [HOURS METER],
IN, OUT and SPLIT points.
[WARNING], [UMID] and [DIF]. Use the SET button to
? Pressing the SHIFT button simultaneous with this
switch among them.
button in the play list mode allows you to add a clip
[WARNING]:Shows warning selected from a thumbnail display to the play list.
information. ? Press this button after the PF button when the
[HOURS METER]:Shows the unit serial THUMBNAIL and PLAY LIST buttons are off to obtain
number, the number of access to the setup menu registered using the PF2
hours it has been on, and button.
the number of times it has
been switched on and off.
9.TRIM+/SLOT SELECT+ button
[UMID]:Shows UMID information
Hold down the IN, OUT, or SPLIT button and press this
for the current video.
button in the play list mode to shift the IN, OUT, or
[DIF];Shows various information
SPLIT point 1 frame backward.
on the current DIF (the
While the PLAY LIST button is off, hold down the SHIFT
IEEE 1394 interface).
button and this button simultaneously to move to the
previous recording slot position. Pressing this button
6.IN/SLOT CLIP/PF1 button when the unit is in slot 6 results in a move to slot 1.
Use these functions to create play lists. Press the
ENTRY button and this button simultaneously when
10.OUT/ALL CLIP/PF3 button
registering an event (when the PLAY LIST button and
Use these functions to create play lists. Press the
the EVENT button are both on) to set an event IN point.
ENTRY button and this button simultaneously when
Hold down this button and press the RESET button to
registering an event (when the PLAY LIST button and
cancel the IN point of the selected event.
the ENTRY button are both on) to set an event OUT
Å¥Refer to the Section ?Using Play List? (page 61).
point.
? Press the SHIFT button and this button
Hold down this button and press the RESET button to
simultaneously while thumbnails are displayed to
cancel the OUT point of the selected event.
switch the clip display between SELECTED and
Å¥For details, refer to ?Using Play List? (page 61).
specific SLOT.
? Press the SHIFT button and this button
? Press the ENTRY button and this button
simultaneously while thumbnails are displayed to
simultaneously when the PLAY LIST button is off to
return the clip display to ALL.
register a cue-up point.
? Press the ENTRY button and this button
? Press this button after the PF button when the
simultaneously when the PLAY LIST button is off to
THUMBNAIL and PLAY LIST buttons are off to obtain
register a cue-up point.
access to the setup menu registered using the PF1
? Press this button after the PF button when the
button.
THUMBNAIL and PLAY LIST buttons are off to obtain
access to the setup menu registered using the PF3
7.TRIM-/SLOT SELECT- buttonbutton.
Hold down the IN, OUT, or SPLIT button and press this
button in the play list mode to shift the IN, OUT, or
11.SHIFT button
SPLIT point 1 frame forward.
Use this button together with the FF, REW and SET
Hold down the SHIFT button and this button
buttons.
simultaneously when the PLAY LIST button is off to
Introduction: Control Reference Guide
21 |
ACEC
