Setup menus (continued)
USER menu <OPERATION>
No./ItemDescriptionNo./ItemDescription
114This selects whether to cause the160This sets the repeat play mode.
REC INH lamp to flash or light up
REC INHwhen the cassette has been set to theMEMORY0000OFF :
LAMPaccidental erasure prevention status.MODENo repeat play (normal operation)
0001 M-STOP :
0000 LIGHT : The lamp lights up.The tape stops near the BEGIN point when a
0001 FLASH : The lamp flashes.FF or REW operation has been performed.
Note:0002 REPT1 :
When the REC INHIBIT switch is set toDuring playback, the tape is rewound to the
ON, the REC INH lamp always lightsBEGIN point and stopped when the END
regardless of the general setting status.point is reached.
0003 CONT :
115This selects whether to enable orDuring playback, the tape is rewound to the
disable the operation of the EJECTBEGIN point and then played, and these
EJECT SWbutton on the front panel.steps are repeated when the END point is
INHreached.
0000REC :
161This sets the BEGIN point in the
Operation is disabled while the unit
is in the recording mode.repeat play mode.
0001OFF :CTL BGN
Operation is enabled in all modes.orWhether TC or CTL is displayed on the counter
TC BGNwhen the COUNTER button is pressed is set
120This selects the modes for thehere. When there is no setting, --:--:--:-- appears,
picture and sound output when theand the tape start serves as the BEGIN point.
EJECT EE SELtape is ejected.
162This sets the END point in the
repeat play mode.
0000EE : EE mode
0001 BLACK :END
Whether TC or CTL is displayed on the counter
The picture turns black, and the
sound is muted.when the COUNTER button is pressed is set
here. When there is no setting, --:--:--:-- appears,
0002 GRAY :and the tape end serves as the END point.
The picture turns gray, and the
sound is muted.163
This sets the output image when the
Note:tape returns to the BEGIN point in
The IEEE 1394 digital output video will
be black even if GRAY is selected.REPT MODEthe repeat play mode.
121This selects whether the EE mode or0000 FREEZE :
playback mode is to be establishedThe tape returns to the BEGIN point
while the playback image at the
F/R EE SELduring fast forwarding or rewinding.END point remains frozen.
0000EE : EE mode0001 BLACK :
0001 TAPE : Playback modeThe tape returns to the BEGIN point while
122This select whether the EE mode ora BLACK picture remains on the screen.
0002 EE_SEL :
playback mode is to be establishedThe tape returns to the BEGIN point
STOP EE SELwhen operation is stopped.
with an image which is in
compliance with the setup menu
0000EE : EE mode
0001 TAPE : Playback modeitem No.121 (F/R EE SEL) setting.
Note:
Note:If, when FREEZE has been selected, the
The selection is complied with even in the
END point has been set at the tape end,
standby OFF mode. However, the picturethe playback image will not be frozen
will turn gray (black for IEEE 1394 digital
output) when TAPE is selected.properly. Set the END point in a range
where pictures have been recorded.
USER menu <INTERFACE>
No./ItemDescription
202This sets the ID information to be
returned to the controller.
ID SEL
0000 OTHER :
0001 DVCPRO :
0002ORIG :
Notes:
Y ID information of any VTR except for
The underlined items indicates the initial setting.the DVCPROOs is set in OTHER.
Y The ORIG setting should only be used
YA93P This appears only when the optional boardwhen a Panasonic controller (AG-A850
AJ-YA93P has been installed.YA93Petc. sold separately) is connected.
� 24 � |
ACEC
