PANASONIC AJSD93P Instruction Manual

Setup menus (continued)
USER menu <TIME CODE>
No./ItemDescriptionNo./ItemDescription
500For selecting whether to output the505This selects the time code to be
VITC signal at the positions selected byused when an external time code is
VITC BLANKsetup menu items No. 501 (VITC POS-1)EXT TC SELto be used.
and No. 502 (VITC POS-2).
0000 LTC :
0000 BLANK :The LTC of the TIME CODE IN
VITC signals are not output.connector is used.
0001THRU :0001 VITC :
VITC signals are output.The VITC of the input video signal
or the timecode of the IEEE 1394
501This sets the position where the
digital input signal is used.
VITC signal is to be inserted.
Note:
VITC POS-1Operation uses the VITC setting if AJ-
(For AJ-SD93P)(For AJ-SD93E)YA93PYA93P is not installed.
000010L00007L
506This sets the usage status of the
::::
user bit of the time code generated
000616L000411L
BINARY GPby the TCG.
::::
001020L001522L0000 000 :
NOT SPECIFIED (character set not
Notes:
specified)
Y The same line as the one used for the
setup menu items No. 502 (VITC POS-0001 001 :
2) and No. 662 (UMID POS) settingISO CHARACTER (8 bits character
cannot be set.set based on ISO646, ISO2022)
Y The default settings are not restored0002 010 : UNASSIGNED 1 (undefined)
even if the RESET button is pressed0003 011 : UNASSIGNED 2 (undefined)
while holding down the SEARCH0004 100 : UNASSIGNED 3 (undefined)
button.0005 101 : PAGE/LINE
0006 110 : UNASSIGNED 4 (undefined)
502This sets the position where the0007 111 : UNASSIGNED 5 (undefined)
VITC signal is to be inserted.
507This selects whether to control the
VITC POS-2
phase correction of the LTC which
(For AJ-SD93P)(For AJ-SD93E)
PHASEis output from the TIME CODE OUT
000010L00007L
CORRconnector.
::::
000818L000613L
0000 OFF :
::::Phase correction control is not
001020L001522Lperformed.
Notes:0001 ON :
Y The same line as the one used for thePhase correction control is
YA93Pperformed.setup menu items No. 501 (VITC POS-
1) and No. 662 (UMID POS) setting
508This selects whether the CF flag of
cannot be set.
the TCG is to ON.
Y The default settings are not restored
TCG CF
even if the RESET button is pressed
FLAG0000 OFF : CF flag is OFF.
while holding down the SEARCH
0001 ON : CF flag is ON.
button.
509This selects the DF or NDF mode for
503This selects the signal to be
CTL and TCG.
regenerated when the time code
DF MODE
TCG REGENgenerator (TCG) in the REGEN
(For AJ-SD93P)0000 DF :
mode.
The drop frame mode is used.
0001 NDF :
0000 TC&UB :
The non-drop frame mode is used.
Both the time code and user bit are
Note:
regenerated.
DF/NDF switching is valid only when
0001TC :
the CONTROL switch is set to LOCAL
Only the time code is regenerated.
or the setup menu No. 001 (LOCAL
0002UB :
ENA) is set to ENA.
Only the user bit is regenerated.
The underlined items indicates the initial setting.
YA93P This appears only when the optional board
AJ-YA93P has been installed.
� 26 �